|
PART
|
COLOR
|
LOCATION
|
DIAGRAM
|
|
12 VOLT CONSTANT
|
PINK/BLACK (+) and RED (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
STARTER
|
YELLOW (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
STARTER 2
|
N/A
|
|
|
|
IGNITION 1
|
RED/DARK BLUE (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
IGNITION 2
|
N/A
|
|
|
|
IGNITION 3
|
N/A
|
|
|
|
ACCESSORY/HEATER BLOWER 1
|
BLACK/ORANGE (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
ACCESSORY/HEATER BLOWER 2
|
BLACK/WHITE (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
KEYSENSE
|
N/A
|
|
|
|
PARKING LIGHTS ( - )
|
LIGHT GREEN/ORANGE (-) See NOTE #2
|
@ HEADLIGHT SWITCH or BCM GRAY 22 PIN , PIN 5 See NOTE *5, See DAIGRAM
|
11020_LIBERTY_JEEP LIBERTY PARKING LIGHT DIAGRAM.pdf
|
|
PARKING LIGHTS ( + )
|
DO NOT USE!!!
|
|
|
|
POWER LOCK
|
PINK/PURPLE (1-Wire Door Lock System) See NOTE #3
|
@ REAR of FUSE BOX, TOP LEFT Plug, Pin 14, See DIAGRAM
|
24464_LIBERTY_JEEP LIBERTY 1 WIRE JBS UNITS.pdf
|
|
POWER UNLOCK
|
Same wire, See DIAGRAM
|
See DIAGRAMS
|
24464_LIBERTY_JEEP LIBERTY 1 WIRE ALERT SHELBY UNITS.pdf
|
|
LOCK MOTOR WIRE
|
TAN/DARK BLUE (+)
|
@ BACK of FUSE BOX, TOP LEFT Plug, Pin 6
|
|
|
DOOR TRIGGER
|
See NOTE #4
|
@ BCM, See NOTE *5
|
14301_LIBERTY_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf
|
|
DOMELIGHT SUPERVISION
|
YELLOW (-), Requires Part #775 Relay
|
@ REAR of FUSE BOX, TOP LEFT PLUG, PIN 30
|
|
|
TRUNK RELEASE
|
ORANGE/PINK (-)
|
@ BCM, GRAY 26-Pin plug, Pin 17, See NOTE #6
|
|
|
SLIDING POWER DOOR
|
N/A
|
|
|
|
HORN
|
BLACK/RED (-)
|
@ HORN SWITCH
|
|
|
TACH
|
ANY wire NOT DARK GREEN/ORANGE
|
@ any FUEL-INJECTOR or IGNITION COIL
|
|
|
WAIT TO START LIGHT
|
N/A
|
|
|
|
BRAKE
|
WHITE/TAN (+)
|
@ SWITCH ABOVE BRAKE PEDAL
|
|
|
FACTORY ALARM DISARM
|
LIGHT GREEN/ORANGE (-) See NOTE #5
|
@ BCM, GRAY 22-PIN PLUG, PIN 9, See NOTE #6
|
14301_LIBERTY_LIBERTY DISARM DIAGRAM.pdf
|
|
ANTI-THEFT
|
CHRYSLER'S SENTRY KEY, A TRANSPONDER SYSTEM, See NOTE #1
|
TRANSPONDER @ IGNITION SWITCH TUMBLER
|
|
|
NOTES
|
NOTE #1; This vehicle requires the 791 BYPASS MODULE for REMOTE STARTING, an Extra Ignition key is also required and will need to be placed inside the 791 for Operation, to order please go to the SECURITY BYPASS MODULE Page on this website.
NOTE #2: the PARKING LIGHTS require a (-)Negative thru a 1000 Ohm Resistor and an relay part #775, to connect, See DIAGRAM
NOTE #3: to LOCK requires a (-)Negative thru a 1400 Ohm Resistor and UNLOCK requires a (-)Negative thru a 426 Ohm Resistor, some units will also require 2 extra relays part #775, to connect, See DIAGRAM
NOTE #4: the DRIVERS DOOR is a TAN (-) in the GRAY 26-PIN plug, pin 4, the PASSENGER DOOR is a TAN/RED (-) in the GRAY 26-PIN plug, pin 5, the DRIVERS REAR DOOR is a TAN/ORANGE (-) in the GRAY 22-PIN plug, pin 3, the PASSENGER REAR DOOR (-) is a TAN/YELLOW (-) is a TAN/YELLOW (-) in the GRAY 26-PIN plug, pin 22. When connecting to an ALARM SYSTEM use all 4 DOOR TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM
NOTE #5: THE DISARM WIRE REQUIRES A (-)NEGATIVE THRU A 473 OHM RESISTOR AND AN EXTRA RELAY PART #775, TO CONNECT, See DIAGRAM
NOTE #6: THE BCM (Body Control Module) IS ATTACHED TO THE LEFT OF THE FUSE BOX.
|