|
PART
|
COLOR
|
LOCATION
|
DIAGRAM
|
|
12 VOLT CONSTANT
|
RED/ORANGE (+) See NOTE #2
|
@ IGNITION SWITCH HARNESS
|
|
|
STARTER
|
PINK/LIGHT BLUE (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
STARTER 2
|
N/A
|
|
|
|
IGNITION 1
|
PINK/LIGHT GREEN (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
IGNITION 2
|
PINK or BLACK (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
IGNITION 3
|
N/A
|
|
|
|
ACCESSORY/HEATER BLOWER 1
|
PINK/YELLOW (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
ACCESSORY/HEATER BLOWER 2
|
PINK/PURPLE (+) See NOTE #2
|
@ IGNITION SWITCH HARNESS
|
|
|
KEYSENSE
|
N/A
|
|
|
|
PARKING LIGHTS ( - )
|
N/A
|
|
|
|
PARKING LIGHTS ( + )
|
PINK/RED (+) and WHITE/ORANGE (+) must use both, See NOTE #8
|
@ FUSEBOX, BLACK Plug, Pin 6 and 5
|
14301_DURANGO_DUAL PARKING LIGHT DIAGRAM.pdf
|
|
POWER LOCK
|
PURPLE/DARK GREEN (1-Wire Door Lock System), See NOTE #3
|
See NOTE #4
|
4445_DURANGO_DODGE DURANGO II 1 WIRE JBS UNITS.pdf
|
|
POWER UNLOCK
|
Same wire, See DIAGRAM
|
See DIAGRAMS
|
4445_DURANGO_DODGE DURANGO II 1 WIRE ALERT SHEBY UNITS.pdf
|
|
LOCK MOTOR WIRE
|
LIGHT GREEN (+)
|
IN DRIVERS KICK PANEL, at DOOR HARNESS
|
|
|
DOOR TRIGGER
|
See NOTE #6
|
See NOTE #7
|
17044_DURANGO_(-) NEGATIVE DOOR PIN ISOLATION CIRCUIT.pdf
|
|
DOMELIGHT SUPERVISION
|
PURPLE (-), (Requires #775 Relay)
|
See NOTE #7
|
|
|
TRUNK RELEASE
|
N/A
|
|
|
|
SLIDING POWER DOOR
|
N/A
|
|
|
|
HORN
|
DARK GREEN/PURPLE (-)
|
@ STEERING COLUMN HARNESS
|
|
|
TACH
|
ANY wire NOT RED or BROWN/WHITE (AC)
|
@ COIL PACK or FUEL INJECTOR
|
|
|
WAIT TO START LIGHT
|
N/A
|
|
|
|
BRAKE
|
WHITE/TAN (+)
|
@ FUSEBOX, BLACK plug, Pin 19
|
|
|
FACTORY ALARM DISARM
|
DISARMS with FACTORY REMOTE ONLY!!!
|
See NOTE #5
|
|
|
ANTI-THEFT
|
CHRYSLER'S ANTI-THEFT TRANSPONDER System (GRAY IGNITION KEY), See NOTE #1
|
@ IGNITION SWITCH TUMBLER
|
|
|
NOTES
|
NOTE #1: This vehicle may be equipped with CHRYSLER'S ANTI-THEFT TRANSPONDER System
(GRAY IGNITION KEY), if so to remote start will require the 791 BYPASS MODULE and
an extra Ignition key, to order go to the SECURITY BYPASS MODULE PAGE on this
website.
NOTE #2: Vehicles with AUTOMATIC TEMPERATURE CONTROL will have an extra RED/BROWN(+)
12 VOLT Constant and a 3rd ACCESSORY wire, a DARK BLUE (+) that must be
connected.
NOTE #3: this vehicle uses a 1-Wire Door Locking System, LOCK requires a (-)Negative thru
a 330 Ohm resistor and UNLOCK requires a (-)Negative thru a 100 Ohm Resistor,
some units also require 2 extra relays part #775, to connect, See DIAGRAM
NOTE #4: On vehicles WITHOUT MEMORY SEATS, the wire is in the DRIVERS KICK PANEL at the
DOOR HARNESS, in vehicles WITH MEMORY SEATS, the wire is in the DRIVERS DOOR
at the Drivers Memory Mirror Module.
NOTE #5: On some vehicle if the vehicle REMOTE STARTS and then STOPS and repeats this
several times, you may find that it will take up to 1/2 an hour before you can restart
with the IGNITION KEY this is a third layer of CHRYSLER SECURITY and you must
UNLOCK THE DRIVERS door before remote starting to prevent this from occuring.
NOTE #6: the DRIVERS DOOR is a PURPLE (-), the PASSENGER DOOR is a PURPLE/WHITE,
the DRIVERS REAR DOOR is a PURPLE/GREY (-) and the PASSENGER REAR DOOR
is a PURPLE/YELLOW (-) The REAR door wires are in a LARGE 74 Pin plug near
the FUSEBOX. When connecting to an ALARM SYSTEM use all 4 DOOR TRIGGER
wires and DIODE ISOLATE, to connect See DIAGRAM.
NOTE #7: On vehicles WITHOUT MEMORY SEATS, the FRONT DOOR triggers are in the same
plug as the REAR DOORS. WITH MEMORY SEATS, the DRIVERS DOOR trigger is
at the Drivers Memory Mirror Module, and the PASSENGER DOOR trigger is at the
Passenger Memory Mirror Module in the Passenger door.
NOTE #8: this vehicle has 2 PARKING LIGHT wires that will require 2 extra relays part #775 to
connect, See DIAGRAM
|