|
PART
|
COLOR
|
LOCATION
|
DIAGRAM
|
|
12 VOLT CONSTANT
|
RED (+) (X2)
|
@ IGNITION SWITCH HARNESS
|
|
|
STARTER
|
LIGHT BLUE/RED (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
STARTER 2
|
N/A
|
|
|
|
IGNITION 1
|
PINK/LIGHT GREEN (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
IGNITION 2
|
N/A
|
|
|
|
IGNITION 3
|
N/A
|
|
|
|
ACCESSORY/HEATER BLOWER 1
|
PINK/YELLOW (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
ACCESSORY/HEATER BLOWER 2
|
PINK/YELLOW (+)
|
@ IGNITION SWITCH HARNESS
|
|
|
KEYSENSE
|
N/A
|
|
|
|
PARKING LIGHTS ( - )
|
PINK/RED (-) See NOTE #2
|
@ HEADLIGHT Switch or BCM, 22-PIN Plug Pin 5, See NOTE #5
|
14301_LIBERTY_JEEP LIBERTY PARKING LIGHT DIAGRAM.pdf
|
|
PARKING LIGHTS ( + )
|
DO NOT USE!!!
|
|
|
|
POWER LOCK
|
TAN/DARK BLUE (1-Wire Door Lock System) See NOTE #3
|
@ BACK of FUSEBOX, TOP LEFT Plug, Pin 14
|
14301_LIBERTY_JEEP LIBERTY 1 WIRE JBS UNITS.pdf
|
|
POWER UNLOCK
|
Same wire, See DIAGRAM
|
See DIAGRAMS
|
14301_LIBERTY_JEEP LIBERTY 1 WIRE ALERT SHELBY UNITS.pdf
|
|
LOCK MOTOR WIRE
|
TAN/DARK BLUE (+)
|
@ BACK of FUSE BOX, TOP LEFT Plug, Pin 6
|
|
|
DOOR TRIGGER
|
See NOTE #4
|
@ BCM, See NOTE #5
|
|
|
DOMELIGHT SUPERVISION
|
BLACK/WHITE (-) or YELLOW/LIGHT BLUE (-) Requires Part #775 Relay
|
@ BACK of FUSEBOX, TOP LEFT Plug, Pin 30
|
|
|
TRUNK RELEASE
|
LIGHT GREEN/WHITE (-)
|
@ BCM, 26-PIN PLUG, PIN 17, See NOTE #5
|
|
|
SLIDING POWER DOOR
|
N/A
|
|
|
|
HORN
|
DARK GREEN/PURPLE (-)
|
@ HORN SWITCH
|
|
|
TACH
|
Any wire NOT RED/ORANGE or PINK/GRAY, (AC)
|
@ ANY FUEL-INJECTOR or IGNITION COIL
|
|
|
WAIT TO START LIGHT
|
N/A
|
|
|
|
BRAKE
|
WHITE/TAN (+)
|
@ SWITCH ABOVE BRAKE PEDAL
|
|
|
FACTORY ALARM DISARM
|
DISARMS with FACTORY REMOTE ONLY!!!
|
|
|
|
ANTI-THEFT
|
TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1
|
TRANSPONDER @ IGNITION SWITCH TUMBLER
|
|
|
NOTES
|
NOTE #1; This vehicle requires the 791 BYPASS MODULE for REMOTE STARTING, an Extra Ignition key is also required and will need to be placed inside the 791 for Operation.
Part # DB-ALL or Part # XK09, either will bypass the Anti-Theft Without the extra key need and will also do keyless entry without the resistors.
to order please go to the SECURITY BYPASS MODULE Page on this website.
NOTE #2: the PARKING LIGHTS require a (-)Negative thru a 910 Ohm Resistor and an extra Relay part #775, to connect, See DIAGRAM
NOTE #3: to LOCK requires a (-)Negative thru a 1400 Ohm Resistor and UNLOCK requires a (-)Negative thru a 426 Ohm Resistor, some units will also require 2 extra relays part #775, to connect, See DIAGRAM
NOTE #4: the DRIVERS DOOR is a TAN (-) in the GRAY 26-PIN plug, pin 4, the PASSENGER DOOR is a TAN/RED (-) in the GRAY 26-PIN plug, pin 5, the DRIVERS REAR DOOR is a TAN/ORANGE (-) in the GRAY 22-PIN plug, pin 3, the PASSENGER REAR DOOR (-) is a TAN/YELLOW (-) is a TAN/YELLOW (-) in the GRAY 26-PIN plug, pin 22. When connecting to an ALARM SYSTEM, use all 4 DOOR TRIGGER wires and DIODE ISOLATE, to connect, See DIAGRAM
NOTE #5; THE BCM (Body Control Module) IS ATTACHED TO THE LEFT OF THE FUSE BOX.
|