PRINT
MAZDA MAZDA 6
MODEL YEAR(S
MAZDA 6 2009-2013
KEY T-HARNESS IMMOBILIZER
N/A N/A MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, VEHICLES WITH PUSH TO START REQUIRE INTERFACE FOR REMOTE STARTING, See NOTE #1
PART COLOR LOCATION DIAGRAM
12 VOLT CONSTANT RED/BLUE (+) @ IGNITION SWITCH, (6-PIN PLUG), PIN F
STARTER GRAY/RED (+) @ IGNITION SWITCH, (6-PIN PLUG), PIN A
STARTER 2 N/A
IGNITION 1 GREEN/YELLOW (+) @ IGNITION SWITCH, (6-PIN PLUG), PIN C
IGNITION 2 N/A
IGNITION 3 N/A
ACCESSORY/HEATER BLOWER 1 PINK/YELLOW (+) @ IGNITION SWITCH, (6-PIN PLUG), PIN B
ACCESSORY/HEATER BLOWER 2 YELLOW (+) @ IGNITION SWITCH, (6-PIN PLUG), PIN D
KEYSENSE N/A
PARKING LIGHTS ( - ) BLACK/WHITE (-) @ HEADLIGHT SWITCH, (17-PIN PLUG), PIN L
PARKING LIGHTS ( + ) RED/BLUE (+) @ BCM,(16-PIN PLUG(8), PIN O, NOTE #2
POWER LOCK BLACK/WHITE (TYPE B)(-) Negative through 1k resistor. See NOTE #3 @ BCM,(16-PIN PLUG(6), PIN G, NOTE #2
POWER UNLOCK Same as POWER LOCK, Straight ground to UNLOCK
LOCK MOTOR WIRE YELLOW (5-Wire Type) @ BCM,(16-PIN PLUG(7), PIN I, NOTE #2
DOOR TRIGGER BLACK/YELLOW (-) N.C. @ BCM,(16-PIN PLUG(8), PIN B, NOTE #2
DOMELIGHT SUPERVISION BLACK/BLUE (-) @ BCM,(16-PIN PLUG(6), PIN M, NOTE #2
TRUNK RELEASE BLACK/RED (-) @ BCM,(30-PIN PLUG(3), PIN X, NOTE #2
SLIDING POWER DOOR N/A
HORN BLACK (-) @ BCM,(30-PIN PLUG(3), PIN V, NOTE #2
TACH Any wire NOT RED(4 Cyl) or BLUE(V6) (AC) @ Any FUEL-INJECTOR
WAIT TO START LIGHT N/A
BRAKE RED/WHITE (+) @ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle
FACTORY ALARM DISARM Disarms with INTERFACE MODULE, See NOTE #4
ANTI-THEFT MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1
NOTES
NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM,

for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an

Extra Ignition key. (Requires extra key for Operation)



Part # PK-ALL FOR REMOTE STARTING ONLY, requires 2 keys for

programming, NO key required for Operation.



Part # DBALL2 for Remote Starting and Keyless Entry operation (no resistors

required), 2 keys required for programming, no key required for Operation. VEHICLES WITH SMART KEY AND PUSH TO START REQUIRE DBALL2($99) INTERFACE FOR REMOTE STARTING. To Order CALL Tech Support at 800 561 1110 EX. 2146.





NOTE #2: the BCM, (Body Control Module) is located in the DRIVERS KICK PANEL.





NOTE #3: This Vehicle has a NEGATIVE 1-wire door lock system and requires a 1000 ohm 1/2 or 1/4 watt resistor on the LOCK

output from remote starter or keyless entry.

A NEGATIVE pulse through a 1000ohm resistor will LOCK the doors and a straight ground pulse will UNLOCK the doors.





NOTE #4: this Vehicle ARMS/DISARMS with INTERFACE BYPASS MODULE





NOTE #5: TEST this wire while Opening the Trunk/Lift gate from the Release Button on the

REAR of the Vehicle.
LINK 1 LINK TEXT 1 LINK 2 LINK TEXT 2