Back to Lancia Menu
Beta 1300, Beta 1400
1297/1438 cc
1972-81
Engine Code 828A.000
Ignition Data
Ignition system type: CB
Ignition coil make/type: Lu/DLB101
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 2.6-2.8 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Ma/S147CX
Contact breaker gap/air: 0.4 mm
Dwell angle: 52-58 Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Bosch
Spark plug type: W6DC
Electrode gap: 0.6 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/2.8-3.2 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: 12.5-13.0 bar
Oil pressure: 4-5/- bar/eng/rpm
Radiator pressure cap: n / a bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 37/2000
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Ma/E100
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 4182425
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Lancia Menu
Beta 1600,
1585 cc
1972-81
Engine Code 828B.000
Ignition Data
Ignition system type: CB
Ignition coil make/type: Lu/DLB101
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 2.6-2.8 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Ma/S147CX
Contact breaker gap/air: 0.4 mm
Dwell angle: 52-58 Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Bosch
Spark plug type: W5DC
Electrode gap: 0.6 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/2.8-3.2 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: 12.5-13.0 bar
Oil pressure: 4-5/- bar/eng/rpm
Radiator pressure cap: n / a bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 37/2000
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Ma/E95/2.09kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: n / a
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Lancia Menu
Beta 1800,
1756 cc
1972-76
Engine Code 828A1.000
Ignition Data
Ignition system type: CB
Ignition coil make/type: Lu/DLB101
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 2.6-2.8 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Ma/S147CX
Contact breaker gap/air: 0.4 mm
Dwell angle: 52-58 Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Bosch
Spark plug type: W5DC
Electrode gap: 0.6 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/2.8-3.2 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: 12.5-13.0 bar
Oil pressure: 4-5/- bar/eng/rpm
Radiator pressure cap: n / a bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 37/2000
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: n / a
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: n / a
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Lancia Menu
Beta/Trevi,
2000/i/i.e
1995 cc
1975-81
Engine Code 828B1.000
Ignition Data
Ignition system type: CB
Ignition coil make/type: Lu/DLB101
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 2.6-2.8 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Ma/S147CX
Contact breaker gap/air: 0.4 mm
Dwell angle: 52-58 Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Bosch
Spark plug type: W6DC
Electrode gap: 0.5-0.6 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/- bar
Engine idle speed: 825 25 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: 12.5-13.0 bar
Oil pressure: 4-5/- bar/eng/rpm
Radiator pressure cap: n / a bar/type
Drive belt 1 - size: 9.5x110 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 60/3500
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: n / a
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 4201739
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Lancia Menu
Beta Coupe, 1300
1367 cc
1982-86
Engine Code 828D3.000
Ignition Data
Ignition system type: El-i
Ignition coil make/type: Ma/BAE 207A
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 0.75-0.81 Ohms
Secondary resistance: 9500-11500 Ohms
Distributor make/type: Ma/SM806AX
Contact breaker gap/air: n / a mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Marelli
Spark plug type: CW78LP
Electrode gap: 0.6-0.7 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/2.8-3.2 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: n / a bar
Oil pressure: 3.9-5.9/- bar/eng/rpm
Radiator pressure cap: n / a bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 40/2500
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Ma/E100/1.2kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 4182425
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Lancia Menu
Beta 1600, Coupe/HPE
1585 cc
1982
Engine Code 828B.000
Ignition Data
Ignition system type: El-i
Ignition coil make/type: Bo/0 221 122 012
Supply voltage: 5.7 + Volts with ballast resistor
Primary resistance: 1.2-1.6 Ohms
Secondary resistance: 6300-10200 Ohms
Distributor make/type: Bo/0 237 002 056
Contact breaker gap/air: n / a mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: O/S/F
Firing Order: 1-3-4-2
Spark plug make: Marelli
Spark plug type: CW78LP
Electrode gap: 0.6-0.7 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/2.8-3.2 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: n / a bar
Oil pressure: 3.9-5.9/- bar/eng/rpm
Radiator pressure cap: 0.5 bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 50/3000
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Ma/E95/0.9kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: n / a
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Lancia Menu
Beta/Trevi 2.0,
Coupe/HPE
1995 cc
1982-88
Engine Code 828B1.000
Ignition Data
Ignition system type: El-i
Ignition coil make/type: Bo/0 221 122 012
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 1.2-1.6 Ohms
Secondary resistance: 6000-10000 Ohms
Distributor make/type: Bo/0 237 001 004
Contact breaker gap/air: n / a mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: O/S/F
Firing Order: 1-3-4-2
Spark plug make: Marelli
Spark plug type: CW78LP
Electrode gap: 0.6-0.7 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Mech/2.8-3.2 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: n / a bar
Oil pressure: n / a bar/eng/rpm
Radiator pressure cap: 0.98 bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 55/3500
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Bo/100/1.1kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 4201739
Tyre pressures: 1.7(24)f 1.7(24)r bar (psi)
Back to top of page or Lancia Menu
Beta/Trevi IE,
Coupe/HPE
1995 cc
1981-87
Engine Code 828B4.000
Ignition Data
Ignition system type: El-ecu
Ignition coil make/type: Ma/BAE 500B
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 0.42-0.46 Ohms
Secondary resistance: 3330-4070 Ohms
Distributor make/type: Ma/SM808GXK
Contact breaker gap/air: n / a mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 10/800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: O/S/F
Firing Order: 1-3-4-2
Spark plug make: Marelli
Spark plug type: CW78LP
Electrode gap: 0.6-0.7 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Elec/2.4-3.6 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.0-3.0 Vol %
Engine Data
Valve clearance - inlet: 0.42 c mm
(cold)
Valve clearance - exhaust: 0.48 c mm (cold)
Compression pressure: 12.5-13.0 bar
Oil pressure: 4-5/- bar/eng/rpm
Radiator pressure cap: 0.98 bar/type
Drive belt 1 - size: 9.5x1100 KDB110 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 60/3500
Amps/eng/rpm
Regulated output: 13.9-14.8 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Bo/100/1.1kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 15/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 4201739
Tyre pressures: 1.7(24)f 1.7(24)r bar (psi)
Back to top of page or Lancia Menu.