325i, (E36), ,2494 cc, 1991-92, Engine Code 25 6S 1
Ignition Data
Ignition system type: DIS
Ignition coil make/type: Bo/0 221 504 410
Supply voltage: 11 - Volts without ballast resistor
Primary resistance: 0.3-0.5 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Bo/0 261 200 405
Contact breaker gap/air: n / a mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: n / a Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-5-3-6-2-4
Spark plug make: Bosch
Spark plug type: F03DAR
Electrode gap: 0.8-0.9 mm
Fuel System
Fuel type: U
Fuel pump type/pressure: Elec/2.94-3.06 bar
Engine idle speed: 700 40 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 0.5-1.5 Vol
Engine Data
Valve clearance - inlet: Hyd
Valve clearance - exhaust: Hyd
Compression pressure: 10-11 bar
Oil pressure: 4.0/- bar/eng/rpm
Radiator pressure cap: 0.9-1.1 bar/type
Drive belt 1 - size: n / a mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: n / a Amps/eng/rpm
Regulated output: 13.5-14.2 Volts
Battery: 12/66 V/Ah
Starter motor make/type: Bo/0 001 311 125
Other Data
Clutch operation type: Hyd
Clutch adjustment: S/Adj. mm
Cambelt failure: n / a
Cambelt Part Number: n / a
Tyre pressures: 2.0(28)f 2.4(34)r bar (psi)
Babk to page top or return to menu
518i, (E28), 1766 cc, 1985-88, Engine Code 18 4E Y
Ignition Data
Ignition system type: El-i
Ignition coil make/type: Bo/0 221 122 319
Supply voltage: 10.8 - Volts without ballast resistor
Primary resistance: 0.82 Ohms
Secondary resistance: 8250 Ohms
Distributor make/type: Bo/0 237 002 102
Contact breaker gap/air: 0.30-0.70 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 23/3000 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 30/3000 Deg eng/rpm (without vacuum)
Timing mark location: Flywheel
No 1 plug location: Pulley
Firing Order: 1-3-4-2
Spark plug make: Bosch
Spark plug type: W8DC
Electrode gap: 0.6 mm
Fuel System
Fuel type: L/U
Fuel pump type/pressure: Elec/2.94-3.06 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 1.5 Max Vol %
Engine Data
Valve clearance - inlet: 0.20 c mm (cold)
Valve clearance - exhaust: 0.20 c mm (cold)
Compression pressure: 10-12 bar
Oil pressure: 4-6/6000 bar/eng/rpm
Radiator pressure cap: 1.0 KRB250 bar/type
Drive belt 1 - size: 9.5X875 KDB875 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 80/2500 Amps/eng/rpm
Regulated output: 13.5-14.2 Volts
Battery: 12/44 V/Ah
Starter motor make/type: Bo/0 001 311 100
Other Data
Clutch operation type: Hyd
Clutch adjustment: S/Adj. mm
Cambelt failure: n / a
Cambelt Part Number: n / a
Tyre pressures: 2.0(28)f 2.0(28)r bar (psi)
Babk to page top or return to menu
525i, (E28), 2494 cc, 1983-88, Engine Code M30-B25
Ignition Data
Ignition system type: EI-i
Ignition coil make/type: Bo/0 221 122 319
Supply voltage: 10.8 - Volts without ballast resistor
Primary resistance: 0.82 Ohms
Secondary resistance: 7300-8300 Ohms
Distributor make/type: Bo/0 237 302 026
Contact breaker gap/air: 0.30-0.70 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: n / a Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 22/1800 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-5-3-6-2-4
Spark plug make: Bosch
Spark plug type: W8DC
Electrode gap: 0.7 mm
Fuel System
Fuel type: L
Fuel pump type/pressure: Elec/2.8-3.4 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 1.5 Max Vol %
Engine Data
Valve clearance - inlet: 0.30 c mm (cold)
Valve clearance - exhaust: 0.30 c mm (cold)
Compression pressure: 10-11 bar
Oil pressure: 4-6/- bar/eng/rpm
Radiator pressure cap: 1.0 KRB250 bar/type
Drive belt 1 - size: 12.5x1050 KEB105 mm/type
Drive belt 2 - size: 9.5X900 KDB900 mm/type
Electrical System
Alternator output: 55/2500 Amps/eng/rpm
Regulated output: 13.5-14.2 Volts
Battery: 12/55 V/Ah
Starter motor make/type: Bo/0 001 311 100
Other Data
Clutch operation type: Hyd
Clutch adjustment: S/Adj. mm
Cambelt failure: n / a
Cambelt Part Number: n / a
Tyre pressures: 2.0(28)f 2.0(28)r bar (psi)
Babk to page top or return to menu
525i, (E28), 2496 cc, 1984-87, Engine Code 25 6E A
Ignition Data
Ignition system type: EL-i
Ignition coil make/type: Bo/0 221 122 319
Supply voltage: 10.8 - Volts without ballast resistor
Primary resistance: 0.82 Ohms
Secondary resistance: 9500 Ohms
Distributor make/type: Bo/0 237 304 030
Contact breaker gap/air: 0.30-0.70 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 19/2150 98U Deg eng/rpm (without
vacuum)
Ignition Timing - leaded: 22/2150 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-5-3-6-2-4
Spark plug make: Bosch
Spark plug type: W8DC
Electrode gap: 0.7 mm
Fuel System
Fuel type: L/U
Fuel pump type/pressure: Elec/2.3-2.7 bar
Engine idle speed: 850 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 1.5 Max Vol %
Engine Data
Valve clearance - inlet: 0.30 c mm (cold)
Valve clearance - exhaust: 0.30 c mm (cold)
Compression pressure: 10-11 bar
Oil pressure: n / a bar/eng/rpm
Radiator pressure cap: 0.90-1.15 bar/type
Drive belt 1 - size: 12.5x1055 KEB105 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 80/1500 Amps/eng/rpm
Regulated output: 13.5-14.2 Volts
Battery: 12/55 V/Ah
Starter motor make/type: Bo/0 001 311 125
Other Data
Clutch operation type: Hyd
Clutch adjustment: S/Adj. mm
Cambelt failure: n / a
Cambelt Part Number: n / a
Tyre pressures: 2.0(28)f 2.0(28)r bar (psi)
Babk to page top or return to menu