DTC Troubleshooting: P0122 (7) (K20A6 M/T)
DTC Troubleshooting: P0122 (7)
| DTC P0122: | TP Sensor Circuit Low Voltage |
| 1. | Turn the ignition switch ON (II). |
| 2. | Check the TP SENSOR in the DATA LIST with the Honda PGM Tester or the HDS. Is there about 0° (REL), 0 % (REL) or 0.5 V when the throttle is fully closed and about 80° (REL), 100 % (REL) or 4.5 V when the throttle is fully opened? YES - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the TP sensor and the ECM/PCM.n NO - Go to 3. |
| 3. | Turn the ignition switch OFF. |
| 4. | Disconnect the TP sensor 3P connector. |
| 5. | Turn the ignition switch ON (II). |
| 6. | On the wire harness side, measure voltage between the TP sensor 3P connector terminals No. 1 and No. 3. TP SENSOR 3P CONNECTORWire side of female terminalsSG2(GRN/YEL)VCC2 (YEL/BLU) Is there about 5 V? YES - Go to 7. NO - Go to 15. |
| 7. | Turn the ignition switch OFF. |
| 8. | On the sensor side, measure resistance between the TP sensor 3P connector terminals No. 1 and No. 2 with the throttle fully closed. TP SENSOR 3P CONNECTORTerminal side of female terminalsSG2TPSIs there about 0.5-0.9 kW? YES - Go to 9. NO - Go to 16. |
| 9. | On the sensor side, measure resistance between the TP sensor 3P connector terminals No. 2 and No. 3 with the throttle fully closed. TP SENSOR 3P CONNECTORTerminal side of male terminalsTPSVCC2Is there about 5.0 kW? YES - Go to 10. NO - Go to 16. |
| 10. | Jump the SCS line with the Honda PGM Tester or the HDS. |
| 11. | Disconnect ECM/PCM connector A (31P). |
| 12. | On the wire harness side, check for continuity between TP sensor 3P connector terminal No. 2 and body ground. TP SENSOR 3P CONNECTORWire side of female terminalsTPS(RED/BLK) Is there continuity? YES - Repair short in the wire between the TP sensor and ECM/PCM (A29), then go to 17. NO - Go to 13. |
| 13. | Connect ECM/PCM connector terminal A29 to body ground with a jumper wire. ECM/PCM CONNECTOR A (31P)Wire side of female terminalsJUMPER WIRETPS (RED/BLK) |
| 14. | On the wire harness side, check for continuity between TP sensor 3P connector terminal No. 2 and body ground. TP SENSOR 3P CONNECTORWire side of female terminalsTPS(RED/BLK) Is there continuity? YES - Go to 21. NO - Repair open in the wire between the TP sensor and ECM/PCM (A29), then go to 17. |
| 15. | Measure voltage between ECM/PCM connector terminals A20 and A23. ECM/PCM CONNECTOR A (31P)Wire side of female terminalsSG2(GRN/YEL)VCC2 (YEL/BLU) Is there about 5 V? YES - Repair open in the wire between the ECM/PCM (A20) and the TP sensor, then go to 17. NO - Go to 21. |
| 16. | Replace the throttle body (the TP sensor is not available separately). |
| 17. | Turn the ignition switch ON (II). |
| 18. | Do the ECM/PCM RESET in the CLEAR MENU with the Honda PGM Tester or the HDS. |
| 19. | Do the ECM/PCM idle learn procedure. |
| 20. | Check for Temporary DTCs or DTCs in the DTCs MENU with the Honda PGM Tester or the HDS. Are any Temporary DTCs or DTCs indicated? YES - If DTC P0122 is indicated, check for poor connections or loose terminals at the TP sensor and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC troubleshooting. NO - Troubleshooting is complete.n |
| 21. | Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM. |
| 22. | Check for Temporary DTCs or DTCs in the DTCs MENU with the Honda PGM Tester or the HDS. Are any Temporary DTCs or DTCs indicated? YES - If DTC P0122 is indicated, check for poor connections or loose terminals at the TP sensor and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC troubleshooting. NO - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM.n |