DTC Troubleshooting: P0135 (41-2) (5MT)
DTC Troubleshooting: P0135 (41-2)
| DTC P0135 (41-2): | Primary HO2S (Sensor 1) Heater Circuit Malfunction |
| 1. | Reset the ECM/PCM. |
| 2. | Start the engine. Is DTC P0135 indicated? YES - Go to 3. NO - Intermittent failure, system is OK at this time. Check for poor connections or loose wires at the primary HO2S (Sensor 1) and at the ECM/ PCM.n |
| 3. | Turn the ignition switch OFF. |
| 4. | Disconnect the primary HO2S (Sensor 1) 4P connector. |
| 5. | At the primary HO2S side, measure resistance between the primary HO2S (sensor 1) 4P connector terminals No. 3 and No. 4.
 PRIMARY HO2S (SENSOR 1) 4P CONNECTORTerminal side of male terminalsIs there about 6 W (at room temperature)? YES - Go to 6. NO - Replace the primary HO2S (Sensor 1).n |
| 6. | Check for continuity between body ground and the primary HO2S (Sensor 1) 4P connector terminals No. 3 and No. 4 individually.
 PRIMARY HO2S (SENSOR 1) 4P CONNECTORTerminal side of male terminalsIs there continuity? YES - Replace the primary HO2S (Sensor 1).n NO - Go to 7. |
| 7. | Turn the ignition switch ON (II). |
| 8. | Measure voltage between the primary HO2S (Sensor 1) 4P connector terminal No. 3 and No. 4.
 PRIMARY HO2S (SENSOR 1) 4P CONNECTORPO2SHTC(BLK/WHT)IG1 (BLK/YEL)Wire side of female terminals Is there battery voltage? YES - Go to 9. NO - Go to 13. |
| 9. | Turn the ignition switch OFF. |
| 10. | Disconnect the negative cable from the battery. |
| 11. | Disconnect ECM/PCM connector A (31P). |
| 12. | Check for continuity between ECM/PCM connector terminal A1 and body ground.
 ECM/PCM CONNECTOR A (31P)Wire side of female terminalsPO2SHTC(BLK/WHT) Is there continuity? YES - Repair short in the wire between the ECM/PCM (A1) and the primary HO2S (Sensor 1).n NO - Substitute a known-good ECM/PCM and recheck. If symptom/indication goes away, replace the original ECM/ PCM.n |
| 13. | Measure voltage between the primary HO2S (Sensor 1) 4P connector terminal No. 3 and body ground.
 PRIMARY HO2S (SENSOR 1)4P CONNECTORTerminal side of male terminalsIG1 (BLK/YEL) Is there battery voltage? YES - Go to 14. NO - Check the No. 16 (7.5A) fuse in the under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the primary HO2S (Sensor 1) and No. 16 (7.5A) fuse.n |
| 14. | Turn the ignition switch OFF. |
| 15. | Disconnect the negative cable from the battery. |
| 16. | Reconnect the primary HO2S (Sensor 1) 4P connector. |
| 17. | Disconnect ECM/PCM connector A (31P). |
| 18. | Reconnect the negative cable to the battery. |
| 19. | Turn the ignition switch ON (II). |
| 20. | Measure voltage between ECM/PCM connector terminal A1 and A5.
 ECM/PCM CONNECTOR A (31P)Wire side of female terminalsPO2SHTC(BLK/WHT)PG1(BLK) Is there 0.1 V or less? YES - Repair open in the wire between the ECM/PCM (A1) and the primary HO2S (Sensor 1).n NO - Substitute a known-good ECM/PCM and recheck. If symptom/indication goes away, replace the original ECM/ PCM.n |