POWER DOOR LOCK CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body or Master Switch / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door Courtesy SW
    Rear right door courtesy light switch signal/ON or OFF
    ON: Rear right door open
    OFF: Rear right door closed
    -
    RL Door Courtesy SW
    Rear left door courtesy light switch signal/ON or OFF
    ON: Rear left door open
    OFF: Rear left door closed
    -
    Door Lock SW-Lock
    Front passenger door control switch lock signal/ON or OFF
    ON: Lock side of front passenger door control switch pushed
    OFF: Lock side of front passenger door control switch not pushed
    -
    Door Lock SW-Unlock
    Front passenger door control switch unlock signal/ON or OFF
    ON: Unlock side of front passenger door control switch pushed
    OFF: Unlock side of front passenger door control switch not pushed
    -
    Door Key SW-Lock
    Driver door key-linked lock/unlock switch lock signal/ON or OFF
    ON: Driver door key cylinder turned to lock position
    OFF: Driver door key cylinder not turned to lock position
    -
    D Door Key SW-UL
    Driver door key-linked lock/unlock switch unlock signal/ON or OFF
    ON: Driver door key cylinder turned to unlock position
    OFF: Driver door key cylinder not turned to unlock position
    -
    FR Door Lock Pos
    Front door RH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    -
    FR Door Courtesy
    Front door RH courtesy light switch signal/ON or OFF
    ON: Front door RH open
    OFF: Front door RH closed
    -
    FL Door Lock Pos
    Front door LH unlock detection switch signal/LOCK or UNLOCK
    LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    -
    FL Door Courtesy
    Front door LH courtesy light switch signal/ON or OFF
    ON: Front door LH open
    OFF: Front door LH closed
    -
    RR-Door Lock Pos SW
    Rear door RH unlock detection switch signal/ON or OFF
    ON: Rear door RH unlocked
    OFF: Rear door RH locked
    -
    RL-Door Lock Pos SW
    Rear door LH unlock detection switch signal/ON or OFF
    ON: Rear door LH unlocked
    OFF: Rear door LH locked
    -
    Back Door Courtesy SW
    Back door courtesy switch signal/ ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    Back Door Open
    Back door lock/Permit or Prohibt
    Permit: Back door unlocked
    Prohibt: Back door locked
    -
    Back Door Open Handle SW*1
    Back door opener switch signal/ ON or OFF
    ON: Back door opener switch pushed
    OFF: Back door opener switch not pushed
    -
    Unlock Key Twice
    Key-linked 2-step unlock function/ ON or OFF
    Customized value displayed
    -
    Auto Lock
    Speed-sensitive automatic door lock function/ON or OFF
    Customized value displayed
    -
    Auto Lock/Shift
    Shift-linked automatic door lock function/ON or OFF
    Customized value displayed
    -
    Auto Unlock/Shift
    Shift-linked automatic door unlock function/ON or OFF
    Customized value displayed
    -
    All Unlock/Open-Close
    Driver door-linked automatic door unlock function/ON or OFF
    Customized value displayed
    -
    The Number of DTC
    Number of trouble codes/Min.: 0 or Max.: 255
    Number of DTCs will be displayed
    -
    *1: w/o Entry System Back Door Open Fuction

    Master Switch (Multiplex Network Master Switch Assembly) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Lock Switch Status
    Driver door control switch lock signal/ON or OFF
    ON: Lock side of driver door control switch pushed
    OFF: Lock side of driver door control switch not pushed
    -
    Door Unlock Switch Status
    Driver door control switch unlock signal/ON or OFF
    ON: Unlock side of driver door control switch pushed
    OFF: Unlock side of driver door control switch not pushed
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Door Lock
    Door lock motor
    UNLOCK/LOCK/OFF
    -
    D-Door Unlock
    Driver door lock motor
    ON/OFF
    -
    Shock Detection Unlock
    Door lock motor
    UNLOCK/LOCK
    -
    Trunk and Back-Door Open
    Back door lock motor
    ON/OFF
    -