SLIDING ROOF SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Sliding Roof / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Assembly)) 
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Open Switch
    		SLIDE OPEN switch signal/ON or OFF
    		ON: SLIDE OPEN switch pressed
    OFF: SLIDE OPEN switch not pressed
    		-
    Close Switch
    		SLIDE CLOSE switch signal/ON or OFF
    		ON: SLIDE CLOSE switch pressed
    OFF: SLIDE CLOSE switch not pressed
    		-
    Up Switch
    		TILT UP switch signal/ON or OFF
    		ON: TILT UP switch pressed
    OFF: TILT UP switch not pressed
    		-
    Down Switch
    		TILT DOWN switch signal/ON or OFF
    		ON: TILT DOWN switch pressed
    OFF: TILT DOWN switch not pressed
    		-
    Hall IC1 Pulse
    		Hall IC1 pulse output/Lo or Hi
    		Lo and Hi repeat during motor operation
    		Lo: Hall IC1 output is low
    Hi: Hall IC1 output is high
    Hall IC1 Status
    		Status of Hall IC1/Normal or Error
    		Normal: Hall IC1 is normal
    Error: Hall IC1 is not normal
    		-
    Hall IC2 Pulse
    		Hall IC2 pulse output/Lo or Hi
    		Lo and Hi repeat during motor operation
    		Lo: Hall IC2 output is low
    Hi: Hall IC2 output is high
    Hall IC2 Status
    		Status of Hall IC2/Normal or Error
    		Normal: Hall IC2 is normal
    Error: Hall IC2 is not normal
    		-
    Ignition (Direct Signal)
    		Power switch signal/ON or OFF
    		ON: Power switch on (IG)
    OFF: Power switch off
    		-
    Ignition (MPX)
    		Power switch signal (LIN signal)/ON or OFF
    		ON: Power switch on (IG)
    OFF: Power switch off
    		-
    Door Courtesy
    		Driver door courtesy light switch signal/ON or OFF
    		ON: Driver door open
    OFF: Driver door closed
    		-
    Key Off Permission
    		Key-off sliding roof operation permit signal/ON or OFF
    		ON: Front doors are not opened within 43 seconds after power switch was turned off
    OFF: Any status except "ON" status
    		-
    Open Switch Failure(Past)
    		Open switch failure signal (Past)/ON or OFF
    		ON: Sliding roof open switch failure signal (Past)
    OFF: No sliding roof open switch failure signal (Past)
    		-
    Close Switch Failure(Past)
    		Close switch failure signal (Past)/ON or OFF
    		ON: Sliding roof close switch failure signal (Past)
    OFF: No sliding roof close switch failure signal (Past)
    		-
    Up Switch Failure(Past)
    		Up switch failure signal (Past)/ON or OFF
    		ON: Sliding roof tilt up switch failure signal (Past)
    OFF: No sliding roof tilt up switch failure signal (Past)
    		-
    Down Switch Failure(Past)
    		Down switch failure signal (Past)/ON or OFF
    		ON: Sliding roof tilt down switch failure signal (Past)
    OFF: No sliding roof tilt down switch failure signal (Past)
    		-
    Open Switch Failure(Current)
    		Open switch failure signal (Current)/ON or OFF
    		ON: Sliding roof open switch failure signal (Current)
    OFF: No sliding roof open switch failure signal (Current)
    		-
    Close Switch Failure(Current)
    		Close switch failure signal (Current)/ON or OFF
    		ON: Sliding roof close switch failure signal (Current)
    OFF: No sliding roof close switch failure signal (Current)
    		-
    Up Switch Failure(Current)
    		Up switch failure signal (Current)/ON or OFF
    		ON: Sliding roof tilt up switch failure signal (Current)
    OFF: No sliding roof tilt up switch failure signal (Current)
    		-
    Down Switch Failure(Current)
    		Down switch failure signal (Current)/ON or OFF
    		ON: Sliding roof tilt down switch failure signal (Current)
    OFF: No sliding roof tilt down switch failure signal (Current)
    		-
    Number of Trouble Codes
    		Number of trouble codes/Min.: 0 or Max.: 255
    		Number of DTCs will be displayed
    		-


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Sliding Roof / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Assembly)) 
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Slide Roof
    		Operate sliding roof
    		Opn/Dwn / Clos/Up / OFF
    		-