ENTRY AND START SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Power Source Control / Data List.

  5. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Stop Light Switch1
    		State of brake pedal/ON or OFF
    		ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The hybrid control system cannot be started when this item is "OFF".
    3. When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.
    Start Switch1
    		Condition of power switch contact 1/ON or OFF
    		ON: Power switch pressed
    OFF: Power switch not pressed
    1. If the power switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the power switch input signal is malfunctioning.
    Start Switch2
    		Condition of power switch contact 2/ON or OFF
    		ON: Power switch pressed
    OFF: Power switch not pressed
    1. This is the backup for power switch 1.
    2. Behaves the same way as power switch 1.
    Latch Circuit
    		Condition of IG related backup circuit (IG hold circuit)/ON or OFF
    		ON: Power switch on (IG)
    OFF: Power switch off
    		This item behaves in almost the same way as the IG1 and IG2 relays.
    IG1 Relay Monitor (Outside)
    		IG1 relay activation/ON or OFF
    		ON: IG1 relay on
    OFF: IG1 relay off
    		As this is the IG1 relay ON signal, this item displays "OFF" when the power switch is on (ACC).
    IG1 Relay Monitor (Inside)
    		IG1 relay activation/ON or OFF
    		ON: IG1 relay on
    OFF: IG1 relay off
    		As this is the IG1 relay ON signal, this item displays "OFF" when the power switch is on (ACC).
    IG2 Relay Monitor (Outside)
    		IG2 relay activation/ON or OFF
    		ON: IG2 relay on
    OFF: IG2 relay off
    		As this is the IG2 relay ON signal, this item displays "OFF" when the power switch is on (ACC).
    IG2 Relay Monitor (Inside)
    		IG2 relay activation/ON or OFF
    		ON: IG2 relay on
    OFF: IG2 relay off
    		As this is the IG2 relay ON signal, this item displays "OFF" when the power switch is on (ACC).
    Starter Request Signal
    		Condition of hybrid control system start command signal/ON or OFF
    		ON: Power switch pressed and held while carrying key with park (P) selected and brake pedal depressed
    OFF: Power switch released after approximately 1 second elapses
    1. This item displays "ON" when starting the hybrid control system.
    2. The hybrid control system cannot be started when this item is "OFF".
    ACC Relay Monitor
    		ACC relay activation/ON or OFF
    		ON: ACC relay on
    OFF: ACC relay off
    		This item displays "OFF" when starting the hybrid control system.
    Ready Signal
    		Status of the ready signal/ON or OFF
    		ON: Hybrid control system on (on (READY))
    OFF: Hybrid control system off
    		-
    Vehicle Speed Signal
    		Vehicle moving or stationary/Stop or Run
    		Run: Vehicle moving at 5 km/h (3 mph) or more
    Stop: Vehicle stopped
    		-
    Shift P Signal Pulse
    		Status of the shift P signal pulse/Unknown, Error2, Normal2, Error1, Normal3, Error3 or Normal1
    		Unknown: Other
    Error2: Signal abnormal and park (P) selected
    Normal2: Signal normal and park (P) selected
    Error1: Signal abnormal and park (P) state cannot be determined
    Normal3: Signal normal and R, N, D or B selected
    Error3: Signal abnormal and R, N, D or B selected
    Normal1: Signal normal and park (P) state cannot be determined
    		Use this item to determine if the P position signal is malfunctioning.
    Power Supply Condition
    		State of power supply/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    		All OFF: Power switch off (power supply off)
    ACC ON: Power switch on (ACC) (ACC relay on)
    IG1 ON: Power switch on (IG) (IG1 relay on)
    IG2 ON: Power switch on (IG) (IG2 relay on)
    ST ON: Starting hybrid control system
    		Since IG1 ON and IG2 ON turn "on" at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time).
    Powertrain Type
    		Vehicle identification/HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT, S&S-MMT
    		HV-AT: Hybrid A/T (A/T vehicle equipped with hybrid system)
    		-
    IG1 Circuit
    		IG1 relay coil circuit malfunction/OK or NG
    		OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item when determining whether the IG1 relay is malfunctioning.
    2. The hybrid control system cannot be started when this item displays "NG".
    IG2 Circuit
    		IG2 relay coil circuit malfunction/OK or NG
    		OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item when determining whether the IG2 relay is malfunctioning.
    2. The hybrid control system cannot be started when this item displays "NG".
    Starter Switch Signal Mismatch
    		Power switch signal 1 and 2 mismatch/Yes or No
    		Yes: Switch malfunctioning (power switch signal 1 and 2 do not match)
    No: Switch normal
    		The hybrid control system can be started, even if this item displays "Yes".
    Park Signal Mismatch
    		Park (P) signal malfunction/Yes or No
    		Yes: Signal malfunction (CAN communication and direct line signal do not match)
    No: Signal normal
    		The hybrid control system can be started, even if this item displays "Yes".
    Key Certification Waiting Timed Out
    		Key verification malfunction/Yes or No
    		Yes: Verification error (detected when ID code from key and ID stored in certification ECU (smart key ECU assembly) do not match)
    No: Verification normal
    		The hybrid control system can be started, even if this item displays "Yes".
    Number of Diagnosis Code
    		Number of DTCs/0 to 255
    		Number of DTCs will be displayed
    		-

  6. Enter the following menus: Body / Entry&Start / Data List.

  7. Read the Data List according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Ignition Switch
    		State of certification ECU (smart key ECU assembly) IG power supply input/ON or OFF
    		ON: Power switch on (IG)
    OFF: Power switch off
    		This item displays "OFF" when the power switch is on (ACC).
    # Code
    		Number of DTCs/0 to 255
    		-
    		-
    Steering Lock Sleep Cond
    		Transmission control ECU sleep condition/Yes or No
    		-
    		-
    Steering Lock Start Cond
    		Transmission state of transmission control ECU wake up signal/Yes or No
    		Yes: Wake up signal transmitted
    No: Wake up signal not transmitted
    		-
    Engine Start Condition
    		State of hybrid control system start permission signal determined by transmission control ECU and sent to certification ECU (smart key ECU assembly)/OK or NG
    		OK: Hybrid control system start permitted
    NG: Hybrid control system start prohibited
    1. When this item displays "OK", the certification ECU (smart key ECU assembly) has received an unlock confirmation signal from the transmission control ECU and has permitted hybrid control system start.
    2. The hybrid control system cannot be started when this item displays "NG".
    Engine Start Request
    		Reception state of hybrid control system start permission signal determined by ID code box (immobiliser code ECU) and sent to certification ECU (smart key ECU assembly)/OK or NG
    		OK: Receiving signal
    NG: Not receiving signal
    1. When this item displays "OK", the certification ECU (smart key ECU assembly) has received engine start request signal from the ID code box (immobiliser code ECU) and has permitted hybrid control system start.
    2. The hybrid control system cannot be started when this item displays "NG".
    S Code Check
    		Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)/NG or OK
    		OK: Verification result normal
    NG: Verification result abnormal
    		When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
    2. The gearshift control cannot be locked.
    3. The gearshift control cannot be unlocked (the hybrid control system cannot be started).
    L Code Check
    		Verification result between ID code box (immobiliser code ECU) and transmission control ECU/NG or OK
    		OK: Verification result normal
    NG: Verification result abnormal
    		When a malfunction is present:
    1. The ID code for the ID code box (immobiliser code ECU) or transmission control ECU is not registered or the ID code box (immobiliser code ECU) or transmission control ECU is malfunctioning.
    2. The gearshift control cannot be locked.
    3. The gearshift control cannot be unlocked (the hybrid control system cannot be started).
    Unlock Request Receive
    		Reception state of gearshift control unlock command signal sent to ID code box (immobiliser code ECU) determined by certification ECU (smart key ECU assembly)/NG or OK

    HINT:
    The reception state is maintained for 10 seconds.

    		OK: Within 10 seconds of turning power switch on (IG) or on (ACC) or starting hybrid control system
    NG: Except above
    		If the unlock signal has not been received, the hybrid control system cannot be started.
    If this item does not change to "OK" even though the gearshift control unlock conditions are met, the certification ECU (smart key ECU assembly) or transmission control ECU may be malfunctioning.
    Lock Request Receive
    		Reception state of gearshift control lock command signal sent to ID code box (immobiliser code ECU) determined by certification ECU (smart key ECU assembly)/NG or OK
    		OK: Within 10 seconds of opening any door with power switch off and park (P) selected
    NG: Except above
    		If this item does not change to "OK" even though the gearshift control lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    S Code Check (Past)
    		Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) (Past)/NG or OK
    		OK: Verification result normal
    NG: Verification result abnormal (Past)
    		-
    L Code Check (Past)
    		Verification result between ID code box (immobiliser code ECU) and transmission control ECU (Past)/NG or OK
    		OK: Verification result normal
    NG: Verification result abnormal (Past)
    		-
    Steering Lock
    		State of whether transmission control ECU has determined gearshift control is locked/Unset or Set
    		Set: Gearshift control locked
    Unset: Gearshift control unlocked
    		If this item displays "Unset", the gearshift control does not lock.
    Steering Unlock
    		State of whether transmission control ECU has determined gearshift control is unlocked/Unset or Set
    		Set: Gearshift control unlocked
    Unset: Gearshift control locked
    		If this item displays "Unset", the gearshift control does not unlock (hybrid control system cannot be started).


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relay, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Power Source Control / Active Test.

  5. Perform the Active Test according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Indicator Condition
    		Power switch indicator
    		Green/Red/No Sig
    		Power switch on (READY)

  6. Enter the following menus: Body / Entry&Start / Active Test.

  7. Perform the Active Test according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Power / Engine SW Light
    		Power switch illumination
    		ON/OFF
    		-