FRONT SEAT OUTER BELT ASSEMBLY > DISPOSAL

for Preparation Click here


HINT:
When scrapping vehicles equipped with a seat belt pretensioner or disposing of a front seat outer belt (with a seat belt pretensioner), always deploy the procedures described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.



1. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE)

CAUTION:
  1. Use gloves and safety glasses when handling a front seat outer belt with a deployed pretensioner.
  2. Always wash your hands with water after completing the operation.
  3. Do not apply water, etc. to a front seat outer belt with a deployed pretensioner.
  4. When deploying the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

NOTICE:
  1. Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.
  2. The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.
  3. When deploying a front seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the front seat outer belt.
  4. Be sure to follow the procedure listed below when deploying the seat belt pretensioner.



    B050515E11

  1. Check the function of SST.

    SST
    09082-00700  

    CAUTION:
    When deploying the seat belt pretensioner, always use the specified SST.




      B050511E12

    1. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.
      Text in Illustration 
      *1
      		Battery

      HINT:
      At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



      2. B050514E10

    2. Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

      CAUTION:
      If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.



    B221509E01

  1. Connect SST.

    1. Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

      SST
      09082-00700  
      09082-00770  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



      2. B050513E08

    2. Move SST at least 10 m (33 ft.) away from the front of the vehicle.
      Text in Illustration 
      *a
      		10 m or more

    3. Close all the doors and windows of the vehicle.

      NOTICE:
      Do not damage the SST wire harness.

  1. Deploy the front seat outer belt pretensioner.

    1. Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

    2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.

    3. Press the SST deployment switch to deploy the front seat outer belt pretensioner.

      HINT:
      The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.



    B221506

  1. Dispose of the front seat outer belt assembly.

    1. Remove the front seat outer belt assembly and SST.

    2. Place the outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

      CAUTION:
      1. The outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.
      2. Use gloves and safety glasses when handling an outer belt with a pretensioner that has been deployed.
      3. Always wash your hands with water after completing the operation.
      4. Do not apply water, etc. to a front seat outer belt assembly with a pretensioner that has been deployed.

      HINT:
      When scrapping a vehicle, deploy the front seat outer belt pretensioner, and then scrap the vehicle with the deployed outer belt installed.



2. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

CAUTION:
  1. Use gloves and safety glasses when handling a front seat outer belt with a deployed pretensioner.
  2. Always wash your hands with water after completing the operation.
  3. Do not apply water, etc. to a front seat outer belt with a deployed pretensioner.
  4. When disposing of a pretensioner equipped front seat outer belt, never deploy the belt in the customer's vehicle.

NOTICE:
  1. Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.
  2. The seat belt pretensioner produces an exploding sound when it deploys, so perform the operation outdoors where it will not disturb local residents.
  3. When deploying a front seat outer belt (with a seat belt pretensioner), perform the operation at least 10 m (33 ft.) away from the front seat outer belt.
  4. Be sure to follow the procedure listed below when deploying the seat belt pretensioner.

  1. Remove the front seat outer belt assembly (Click here).



    B121580E04

  1. Wind the seat belt with the retractor.
    Text in Illustration 
    *a
    		Cut
    *b
    		100 mm

  1. When the seat belt is sufficiently wound, cut the seat belt approximately 100 mm (0.393 in.) from the retractor, as shown in the illustration.

    HINT:
    The retractor resistance increases in correlation with how much the seat belt is wound.



    B050515E12

  1. Check the function of SST.

    SST
    09082-00700  

    CAUTION:
    When deploying the seat belt pretensioner, always use the specified SST.




      B050511E12

    1. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.
      Text in Illustration 
      *a
      		Battery

      HINT:
      At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



      2. B050514E10

    2. Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

      CAUTION:
      If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.



    B221509E01

  1. Connect SST.

    1. Connect 2 SST, and then connect them to the front seat outer belt pretensioner.

      SST
      09082-00700  
      09082-00770  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



      2. B221510E01

    2. Place the outer belt on the ground and cover it with a tire and wheel assembly.

      NOTICE:
      Position the front seat outer belt assembly as shown in the illustration.

    3. Position and hold SST at least 10 m (33 ft.) away from the wheel.

      NOTICE:
      Do not damage the SST wire harness.



    B050541E10

  1. Deploy the front seat outer belt pretensioner.
    Text in Illustration 
    *a
    		10 m or more

    1. Check that no one is within a 10 m (33 ft.) radius of the wheel.

    2. Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

    3. Press the SST deployment switch to deploy the front seat outer belt pretensioner.

      HINT:
      The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.



    B221506

  1. Dispose of the front seat outer belt assembly.

    1. Remove the wheel and SST.

    2. Place the outer belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

      CAUTION:
      1. The outer belt becomes very hot when the front seat outer belt pretensioner is deployed, so leave it untouched for at least 30 minutes after it has been deployed.
      2. Use gloves and safety glasses when handling an outer belt with a pretensioner that has been deployed.
      3. Always wash your hands with water after completing the operation.
      4. Do not apply water, etc. to a front seat outer belt assembly with a pretensioner that has been deployed.

      HINT:
      When scrapping a vehicle, deploy the front seat outer belt pretensioner, and then scrap the vehicle with the deployed outer belt installed.