FRONT SEAT OUTER BELT ASSEMBLY > INSPECTION

for Preparation Click here



1. INSPECT FRONT SEAT OUTER BELT ASSEMBLY (w/ Pre-crash Safety System)


    B271725E01

  1. Check the seat belt tension reducer operation. (w/ Seat Belt Tension Reducer System)

    NOTICE:
    Do not apply auxiliary battery voltage to the pretensioner connector.


    1. Connect a positive (+) lead of the auxiliary battery to terminal 1 of the seat belt tension reducer connector and a negative (-) lead to terminal 2.

    2. Check that an operating sound is heard when the magnetized solenoid is attracting the plunger.

    3. Pull out the seat belt and allow it to retract. Listen to the operating sound.

    4. Pull out the seat belt again, disconnect the negative (-) lead of the auxiliary battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.
      Text in Illustration 
      *1
      		Pretensioner Connector
      *2
      		Seat Belt Tension Reducer Connector
      *a
      		Component without harness connected
      (Front Seat Outer Belt Assembly)

      1. If the result is not as specified, replace the front seat outer belt assembly.



    B271726E01

  1. Check the pre-crash seat belt operation.

    1. Measure the resistance according to the value(s) in the table below.
      Standard Resistance 
      Tester Connection
      		Condition
      		Specified Condition
      1 - 2
      		Always
      		Below 1 MΩ
      Text in Illustration 
      *1
      		Pre-crash Seat Belt Connector
      *a
      		Component without harness connected
      (Front Seat Outer Belt Assembly)

      1. If the result is not as specified, replace the front seat outer belt assembly.



    B131510E09

  1. Before installing the outer belt, check the ELR function.

    NOTICE:
    Do not disassemble the retractor.


    1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      Text in Illustration 
      *1
      		Retractor
      *a
      		Unlocked
      *b
      		Locked
      *c
      		45°
      If the result is not as specified, replace the outer belt assembly.



2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY (w/o Pre-crash Safety System)


    B273756E02

  1. Check the seat belt tension reducer operation. (w/ Seat Belt Tension Reducer System)

    NOTICE:
    Do not apply auxiliary battery voltage to the pretensioner connector.


    1. Connect a positive (+) lead of the auxiliary battery to terminal 1 of the seat belt tension reducer connector and a negative (-) lead to terminal 2.

    2. Check that an operating sound is heard when the magnetized solenoid is attracting the plunger.

    3. Pull out the seat belt and allow it to retract. Listen to the operating sound.

    4. Pull out the seat belt again, disconnect the negative (-) lead of the auxiliary battery and allow the seat belt to retract. Listen to the operating sound again and check that the operating sound volume has increased.
      Text in Illustration 
      *1
      		Pretensioner Connector
      *2
      		Seat Belt Tension Reducer Connector
      *a
      		Component without harness connected
      (Front Seat Outer Belt Assembly)

      1. If the result is not as specified, replace the front seat outer belt assembly.



    B131510E09

  1. Before installing the outer belt, check the ELR function.

    NOTICE:
    Do not disassemble the retractor.


    1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      Text in Illustration 
      *1
      		Retractor
      *a
      		Unlocked
      *b
      		Locked
      *c
      		45°
      If the result is not as specified, replace the outer belt assembly.