OUTER MIRROR SWITCH > INSPECTION

for Preparation Click here



1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)


    B273168E01

  1. Check the switch functions (w/ retract mirror).

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      H136-8 (M+) - H136-6 (E)
      		Mirror adjust switch pressed up
      		90 to 110 Ω
      Mirror adjust switch pressed down
      		437 to 503 Ω
      Mirror adjust switch pressed left
      		744 to 856 Ω
      Mirror adjust switch pressed right
      		225 to 275 Ω
      Mirror adjust switch not pressed
      		10 kΩ or higher
      H136-3 (MSW) - H136-6 (E)
      		Mirror select switch R
      		Below 10 Ω
      Mirror select switch L
      		90 to 110 Ω
      Mirror select switch off
      		10 kΩ or higher

      Text in Illustration 
      *1
      		Mirror Adjust Switch
      *2
      		Mirror Select Switch
      *a
      		Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



    B273168E02

  1. Check that the LED illuminates (w/ retract mirror).

    1. Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

      Standard:
      Measurement Condition
      		Specified Condition
      Auxiliary battery positive (+) → H136-9 (ILL+)
      Auxiliary battery negative (-) → H136-1 (ILL-)
      		LED illuminates

      Text in Illustration 
      *a
      		Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check retractable outer mirror switch function.



      B245707E02

    1. Measure the resistance according to the value in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      H137-2 (MR) - H137-3 (E)
      		Retract position
      		Below 1 Ω
      H137-2 (MR) - H137-3 (E)
      		Except retract position
      		10 kΩ or higher
      H137-8 (MF) - H137-3 (E)
      		Return position
      		10 kΩ or higher
      H137-8 (MF) - H137-3 (E)
      		Retract position
      		10 kΩ or higher
      H137-2 (MR) - H137-3 (E)
      		AUTO position
      		Below 1 Ω

      Text in Illustration 
      *a
      		Component without harness connected
      (Retractable Outer Mirror Switch)
      If the result is not as specified, replace the retractable outer mirror switch.

    2. Check that the LED illuminates (w/ retract mirror).



      3. B245707E03

    3. Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

      Standard:
      Measurement Condition
      		Specified Condition
      Auxiliary battery positive (+) → H137-1 (ILL+)
      Auxiliary battery negative (-) → H137-4 (ILL-)
      		LED illuminates

      Text in Illustration 
      *a
      		Component without harness connected
      (Retractable Outer Mirror Switch)
      If the result is not as specified, replace the retractable outer mirror switch.



  1. Check the switch functions (w/o retract mirror).



      B214893E08

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      H37-16 (M+) - H37-14 (E)
      		Mirror adjust switch pressed up
      		90 to 110 Ω
      Mirror adjust switch pressed down
      		437 to 503 Ω
      Mirror adjust switch pressed left
      		744 to 856 Ω
      Mirror adjust switch pressed right
      		255 to 275 Ω
      Mirror adjust switch not pressed
      		10 kΩ or higher
      H37-13 (MSW) - H37-14 (E)
      		Mirror select switch L
      		90 to 110 Ω
      Mirror select switch R
      		Below 1 Ω
      Mirror select switch off
      		10 kΩ or higher

      Text in Illustration 
      *1
      		Mirror Adjust Switch
      *2
      		Mirror Select Switch
      *a
      		Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check that the LED illuminates (w/o retract mirror).



      B214893E09

    1. Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      		Specified Condition
      Auxiliary battery positive (+) → H37-23 (ILL+)
      Auxiliary battery negative (-) → H37-24 (ILL-)
      		LED illuminates

      Text in Illustration 
      *a
      		Component without harness connected
      (Outer Mirror Switch Assembly)



2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)


    B231630E09

  1. Check the switch functions.

    1. Move the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      H38-11 (B) - H38-9 (VL)
      		Mirror adjust switch pressed up
      		Below 1 Ω
      H38-12 (E) - H38-6 (M+)
      		Mirror adjust switch pressed up
      		Below 1 Ω
      H38-11 (B) - H38-6 (M+)
      		Mirror adjust switch pressed down
      		Below 1 Ω
      H38-12 (E) - H38-9 (VL)
      		Mirror adjust switch pressed down
      		Below 1 Ω
      H38-11 (B) - H38-10 (HL)
      		Mirror adjust switch pressed left
      		Below 1 Ω
      H38-12 (E) - H38-6 (M+)
      		Mirror adjust switch pressed left
      		Below 1 Ω
      H38-11 (B) - H38-6 (M+)
      		Mirror adjust switch pressed right
      		Below 1 Ω
      H38-12 (E) - H38-10 (HL)
      		Mirror adjust switch pressed right
      		Below 1 Ω
      H38-11 (B) - H38-12 (E)
      		Always
      		10 kΩ or higher

    3. Move the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      H38-11 (B) - H38-8 (VR)
      		Mirror adjust switch pressed up
      		Below 1 Ω
      H38-12 (E) - H38-6 (M+)
      		Mirror adjust switch pressed up
      		Below 1 Ω
      H38-11 (B) - H38-6 (M+)
      		Mirror adjust switch pressed down
      		Below 1 Ω
      H38-12 (E) - H38-8 (VR)
      		Mirror adjust switch pressed down
      		Below 1 Ω
      H38-11 (B) - H38-7 (RH)
      		Mirror adjust switch pressed left
      		Below 1 Ω
      H38-12 (E) - H38-6 (M+)
      		Mirror adjust switch pressed left
      		Below 1 Ω
      H38-11 (B) - H38-6 (M+)
      		Mirror adjust switch pressed right
      		Below 1 Ω
      H38-12 (E) - H38-7 (RH)
      		Mirror adjust switch pressed right
      		Below 1 Ω
      H38-11 (B) - H38-12 (E)
      		Always
      		10 kΩ or higher

      Text in Illustration 
      *1
      		Mirror Adjust Switch
      *2
      		Mirror Select Switch
      *a
      		Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.



    B231630E10

  1. Check that the LED illuminates.

    1. Apply auxiliary battery voltage to the outer mirror switch assembly and check that the LED illuminates.

      Standard:
      Measurement Condition
      		Specified Condition
      Auxiliary battery positive (+) → H38-15 (ILL+)
      Auxiliary battery negative (-) → H38-16 (ILL-)
      		LED illuminates

      Text in Illustration 
      *a
      		Component without harness connected
      (Outer Mirror Switch Assembly)
      If the result is not as specified, replace the outer mirror switch assembly.