DTC    B1820/55    Short in Side Squib RH Circuit

DTC    B1821/55    Open in Side Squib RH Circuit

DTC    B1822/55    Short to GND in Side Squib RH Circuit

DTC    B1823/55    Short to B+ in Side Squib RH Circuit

for Preparation Click here


DESCRIPTION

The side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH.
The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1820/55
  1. The airbag sensor assembly receives a line short circuit signal in the side squib RH circuit during primary check.
  2. Side squib RH malfunction
  3. Airbag sensor assembly malfunction
  1. No. 2 floor wire
  2. Front seat airbag assembly RH (Side squib RH)
  3. Airbag sensor assembly
B1821/55
  1. The airbag sensor assembly receives an open circuit signal in the side squib RH circuit.
  2. Side squib RH malfunction
  3. Airbag sensor assembly malfunction
B1822/55
  1. The airbag sensor assembly receives a short circuit to ground signal in the side squib RH circuit.
  2. Side squib RH malfunction
  3. Airbag sensor assembly malfunction
B1823/55
  1. The airbag sensor assembly receives a short circuit to B+ signal in the side squib RH circuit.
  2. Side squib RH malfunction
  3. Airbag sensor assembly malfunction

WIRING DIAGRAM


C210621E12


INSPECTION PROCEDURE

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CONNECTORS


    C165140E39

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the front seat airbag assembly RH and airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the front seat airbag assembly RH and airbag sensor assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.

    OK:
    The short spring is not deformed or damaged.

    Text in Illustration 
    *1
    		Front Seat Airbag Assembly RH
    *2
    		Airbag Sensor Assembly
    *3
    		No. 2 Floor Wire



NG
REPLACE NO. 2 FLOOR WIRE
OK


2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)


    C210790E10

  1. Connect the connector to the airbag sensor assembly.

  1. Connect SST (resistance 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat airbag assembly RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.

    Text in Illustration 
    *1
    		Front Seat Airbag Assembly RH
    *2
    		Airbag Sensor Assembly
    *3
    		Connector C
    *a
    		Front view of wire harness connector
    (to Front Seat Airbag Assembly RH)

    HINT:
    Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE FRONT SEAT AIRBAG ASSEMBLY RH (Click here)  

3.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)


    C157614E22

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

  1. Disconnect SST from connector C.

  1. Disconnect the No. 2 floor wire from the airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      		Switch Condition
      		Specified Condition
      Q2-1 (SFR+) - Body ground
      		Power switch on (IG)
      		Below 1 V
      Q2-2 (SFR-) - Body ground
      		Power switch on (IG)
      		Below 1 V

  1. Check for an open in the circuit.

    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      Q2-1 (SFR+) - Q2-2 (SFR-)
      		Always
      		Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      Q2-1 (SFR+) - Body ground
      		Always
      		1 MΩ or higher
      Q2-2 (SFR-) - Body ground
      		Always
      		1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      Q2-1 (SFR+) - Q2-2 (SFR-)
      		Always
      		1 MΩ or higher

      Text in Illustration 
      *1
      		Front Seat Airbag Assembly RH
      *2
      		Airbag Sensor Assembly
      *3
      		No. 2 Floor Wire
      *4
      		Connector C
      *a
      		Front view of wire harness connector
      (to Front Seat Airbag Assembly RH)



NG
REPLACE NO. 2 FLOOR WIRE
OK


4.CHECK AIRBAG SENSOR ASSEMBLY


    C170976E05

  1. Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the power switch off.

  1. Turn the power switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.

    Text in Illustration 
    *1
    		Front Seat Airbag Assembly RH
    *2
    		Airbag Sensor Assembly

    HINT:
    Codes other than DTCs B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)