BLACK OUT TAPE (for Rear Door) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (Click here).



2. REMOVE REAR NO. 2 FLOOR BOARD

  1. Remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX

  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD

  1. Remove the rear No. 3 floor board.



5. REMOVE DECK FLOOR BOX RH


    B270546

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box RH.



6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    B270547

  1. Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B269470

  1. Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.



9. REMOVE REAR DOOR REAR FRAME BRACKET


    B269480

  1. Disengage the clip, 3 claws and 3 guides and remove the rear door rear frame bracket.



10. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B269474

  1. Using a moulding remover, disengage the 3 clips, 4 claws and 2 guides as shown in the illustration.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



11. REMOVE REAR DOOR ARMREST COVER


    B269478

  1. Remove the rear door armrest cover.



12. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B269482E01

  1. Put protective tape around the rear door panel.
    Text in Illustration 
    *1
    		Protective Tape



    B269484

  1. Remove the 2 screws.

  1. Using a clip remover, disengage the 9 clips.



    B269486

  1. Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

  1. Disconnect the connector.



    B269490

  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

  1. Remove the rear door trim board clip (blue) from the rear door trim board.



13. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B269496E01

  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    		Screwdriver



14. REMOVE REAR DOOR SPEAKER COVER (w/o Rear Speaker)


    B269500

  1. Disconnect the connector.

  1. Remove the 3 bolts and rear door speaker cover.



15. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)


    E221218

  1. Disconnect the connector.

  1. Remove the 3 bolts and rear speaker assembly.

    NOTICE:
    Do not touch the speaker cone.



16. REMOVE REAR DOOR TRIM BRACKET


    B269504

  1. Remove the 2 screws and rear door trim bracket.



17. REMOVE REAR DOOR SERVICE HOLE COVER


    B269506

  1. Disengage the clamp.

  1. Disconnect the connector and remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the door.



18. REMOVE REAR DOOR CHECK ASSEMBLY


    B269510

  1. Remove the 3 bolts and rear door check assembly.



19. REMOVE REAR DOOR WEATHERSTRIP


    B269512E01

  1. Using a clip remover, disengage the 23 clips and remove the rear door weatherstrip.
    Text in Illustration 
    *1
    		Double-sided Tape



20. REMOVE REAR DOOR GLASS RUN


    B269514

  1. Remove the rear door glass run.



21. REMOVE NO. 1 REAR DOOR VENT SEAL


    B269518

  1. Remove the No. 1 rear door vent seal.



22. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B269520E01

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    		Temporary Bolt

  1. Remove the bolt and screw and rear door window division bar sub-assembly.

    NOTICE:
    When the rear door window division bar sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  1. Remove the temporary bolt from the rear door window division bar sub-assembly.



23. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B269522

  1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



24. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B269528

  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



25. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B270431E01

  1. Put protective tape around the rear door belt moulding assembly.
    Text in Illustration 
    *1
    		Protective Tape



    B270432E01

  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 5 claws and guide to remove the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    *1
    		Protective Tape



26. REMOVE REAR DOOR FRAME GARNISH


    B269501

  1. Disengage the clip and remove the rear door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing it.



27. REMOVE REAR DOOR OUTSIDE STRIPE

  1. Using a heat light, heat the rear door outside stripe and vehicle body.
    Heating Temperature 
    Item
    		Temperature
    Vehicle Body and Rear Door Outside stripe
    		40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B270454

  1. Pull back on one of the ends of the rear door outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



28. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

  1. Using a heat light, heat the rear door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    		Temperature
    Vehicle Body and Rear Door Lower Outside stripe
    		40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B270455

  1. Pull back on one of the ends of the rear door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.