OUTER REAR VIEW MIRROR > REMOVAL

for Preparation Click here



1. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B266076

  1. Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.



2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B266080

  1. Disengage the clip and claw, and remove the front door lower frame bracket garnish.



3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B266082

  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides as shown in the illustration.

  1. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.



4. REMOVE DOOR ARMREST COVER (for Driver Side)


    B266086

  1. Remove the door armrest cover.



5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Driver Side)


    B266088E01

  1. Put protective tape around the front door panel.
    Text in Illustration 
    *1
    		Protective Tape



    B266090

  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 11 clips.

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the front door trim board sub-assembly and remove it.

  1. w/ Seat Position Memory System:

    1. Disconnect the connector.



    B266094

  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.



6. REMOVE DOOR ASSIST GRIP COVER (for Front Passenger Side)


    B266098

  1. Using a moulding remover, disengage the 4 claws and guide, and remove the door assist grip cover.



7. REMOVE DOOR ASSIST GRIP ASSEMBLY (for Front Passenger Side)


    B266100

  1. Remove the 2 screws.

  1. Disengage the 3 guides and remove the door assist grip assembly.



8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B266102

  1. Using a moulding remover, disengage the 3 clips, 8 claws and 4 guides as shown in the illustration.

  1. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.



9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Passenger Side)


    B266106E01

  1. Put protective tape around the front door panel.
    Text in Illustration 
    *1
    		Protective Tape



    B266108

  1. Remove the 2 screws.

  1. Using a clip remover, disengage the 11 clips.

  1. Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

  1. Raise the front door trim board sub-assembly and remove the front door trim board sub-assembly .



    B266096

  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.



10. REMOVE OUTER MIRROR INSTALL HOLE COVER


    B269252

  1. Remove the screw.

  1. Disengage the 2 claws.

  1. Disengage the clamp and remove the outer mirror install hole cover.



11. REMOVE OUTER MIRROR PROTECTOR


    B269254

  1. Remove the outer mirror protector.

    HINT:
    Remove any remaining adhesive residue on the door.



12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


  1. w/o Memory:



      B269260

    1. Disconnect the connector.

    2. Disengage the clamp.

    3. Remove the 3 nuts.



  1. w/ Memory:



      B269258

    1. Disconnect the connector.

    2. Disengage the clamp.

    3. Remove the 3 nuts.

  1. Disengage the claw and remove the outer rear view mirror assembly.