THEFT DETERRENT SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    RR Door Courtesy SW
    		Rear door courtesy light switch RH/ON or OFF
    		ON: Rear door RH open
    OFF: Rear door RH closed
    		-
    RL Door Courtesy SW
    		Rear door courtesy light switch LH/ON or OFF
    		ON: Rear door LH open
    OFF: Rear door LH closed
    		-
    Back Door Courtesy SW
    		Back door courtesy switch/ON or OFF
    		ON: Back door open
    OFF: Back door closed
    		-
    RR-Door Lock Pos SW
    		Rear door RH unlock detection switch/ON or OFF
    		ON: Rear door RH unlocked
    OFF: Rear door RH locked
    		-
    RL-Door Lock Pos SW
    		Rear door LH unlock detection switch/ON or OFF
    		ON: Rear door LH unlocked
    OFF: Rear door LH locked
    		-
    FR Door Lock Pos
    		Front door RH unlock detection switch/LOCK or UNLOCK
    		LOCK: Front door RH locked
    UNLOCK: Front door RH unlocked
    		-
    FL Door Lock Pos
    		Front door LH unlock detection switch/LOCK or UNLOCK
    		LOCK: Front door LH locked
    UNLOCK: Front door LH unlocked
    		-
    FR Door Courtesy
    		Front door courtesy light switch RH/ON or OFF
    		ON: Front door RH open
    OFF: Front door RH closed
    		-
    FL Door Courtesy
    		Front door courtesy light switch LH/ON or OFF
    		ON: Front door LH open
    OFF: Front door LH closed
    		-
    Hood Courtesy SW
    		Security courtesy switch signal/ON or OFF
    		ON: Engine hood open
    OFF: Engine hood closed
    		-
    Intrusion Sens OFF SW
    		Intrusion sensor cancel switch/ON or OFF
    		ON: Intrusion sensor cancel switch on
    OFF: Intrusion sensor cancel switch off
    		-
    Intrusion Sensor
    		Status of the intrusion sensor detection/ON or OFF
    		ON: Intrusion sensor detected
    OFF: Intrusion sensor not detected
    		-
    Tilt Sensor*
    		Status of the tilt sensor detection/ON or OFF
    		ON: Tilt sensor detected
    OFF: Tilt sensor not detected
    		-
    Intrusion Sen Conn
    		Intrusion sensor connecting/ON or OFF
    		ON: Intrusion sensor connected
    OFF: Intrusion sensor not connected
    		-
    Tilt Sensor Connect*
    		Tilt sensor connecting/ON or OFF
    		ON: Tilt sensor connected
    OFF: Tilt sensor not connected
    		-
    Sealed Glas Brak Sen*
    		Glass breakage sensor connecting/with or without
    		With: Glass breakage sensor connected
    Without: Glass breakage sensor not connected
    		-

    1. *: w/ Combination Meter Assembly with mph Units


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. The Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Main Body / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Hazard
    		Hazard warning lights
    		ON / OFF
    		-
    Security Indicator
    		Security indicator
    		ON / OFF
    		-
    Vehicle Horn
    		Vehicle horns
    		ON / OFF
    		-
    Security Horn2
    		Theft warning siren
    		ON / OFF
    		-
    Power for Intrusion sensor
    		Intrusion sensor power supply
    		ON / OFF
    		-
    Power for Tilt sensor*
    		Tilt sensor power supply
    		ON / OFF
    		-

    1. *: w/ Combination Meter Assembly with mph Units