ROOF HEADLINING > REMOVAL

for Preparation Click here



1. REMOVE REAR NO. 2 FLOOR BOARD

  1. Remove the rear No. 2 floor board.



2. REMOVE REAR DECK FLOOR BOX

  1. Remove the rear deck floor box.



3. REMOVE REAR NO. 3 FLOOR BOARD

  1. Remove the rear No. 3 floor board.



4. REMOVE DECK FLOOR BOX RH


    B270546

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box RH.



5. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    B270547

  1. Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.



6. REMOVE REAR SEAT CUSHION ASSEMBLY


  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.




      B275284E01

    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
      Text in Illustration 
      *1
      		Hook
      *2
      		Guide
      Standard Measurement 
      *a
      		100 mm (3.94 in.) or less

    2. Repeat the step above for the other hook.

  1. Disengage the guide of the seat cushion from the seatback.



    B221512

  1. Remove the bolt and disconnect the rear center seat outer belt assembly.

  1. Pull out the rear center seat outer belt assembly from the rear seat cushion assembly.

  1. Remove the rear seat cushion assembly.



7. REMOVE REAR SEAT CUSHION LOCK HOOK


    B274369

  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure the LH side and RH side.



8. REMOVE REAR SEATBACK ASSEMBLY RH

  1. Disengage the fastener and disconnect the rear No. 1 floor board sub-assembly.



    B275063

  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



9. REMOVE REAR SEATBACK ASSEMBLY LH

  1. Disengage the fastener and disconnect the rear No. 2 floor board sub-assembly.



    B275064

  1. Remove the 2 bolts and rear seatback assembly LH.

    NOTICE:
    Be careful not to damage the vehicle body.



10. REMOVE REAR NO. 4 FLOOR BOARD (w/o Woofer)

  1. Remove the rear No. 4 floor board.



11. REMOVE REAR NO. 4 FLOOR BOARD (w/ Woofer)


    B270548

  1. Disengage the 2 clips and 3 guides, and remove the rear No. 4 floor board.



12. REMOVE DECK FLOOR BOX LH (w/o Woofer)


    B270549

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box LH.



13. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

  1. Remove the tonneau cover assembly.



14. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B270540

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



15. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B270541

  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



16. REMOVE REAR NO. 1 FLOOR BOARD


    B270542

  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



17. REMOVE DECK TRIM SERVICE HOLE COVER


    B270550E01

  1. Disengage the 2 claws and guide (A).

  1. Disengage the 2 guides (B) and remove the deck trim service hole cover.



18. REMOVE REAR DECK TRIM COVER


    B270551

  1. Disengage the 4 clips and remove the rear deck trim cover.



19. REMOVE FRONT SEAT ASSEMBLY
for Manual Seat (Click here)
for Power Seat (Click here)

HINT:
Use the same procedure for the RH side and LH side.



20. REMOVE FRONT DOOR SCUFF PLATE LH


    B270515

  1. Disengage the 4 claws, 2 guides and 4 clips, and remove the front door scuff plate LH.



21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    B270055

  1. Disengage the 2 clips, claw and 2 guides.

  1. Disengage the clamp.

  1. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.



22. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B270517

  1. Remove the clip as shown in the illustration.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.



23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. Remove the front door opening trim weatherstrip LH.

  1. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

    NOTICE:
    Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.



24. REMOVE FRONT PILLAR GARNISH LH


    B270521E01

  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
    Text in Illustration 
    *1
    		Front Pillar Garnish Clip

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.



    B270525E01

  1. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.
    Text in Illustration 
    *1
    		Protective Tape

    NOTICE:
    1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
    2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

    HINT:
    Tape the tips of the needle-nosed pliers before use.

  1. Disengage the 2 guides.

  1. w/o Front Center Speaker:

    1. Remove the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

  1. w/ Front Center Speaker:

    1. Disconnect the front pillar garnish LH by pulling it in the direction indicated by the arrow (2) in the illustration.

    2. Disconnect the connector and remove the front pillar garnish LH.



    B270531E01

  1. Protect the curtain shield airbag assembly.
    Text in Illustration 
    *1
    		Adhesive Tape
    *2
    		Protective Cover
    *3
    		Curtain Shield Airbag Assembly

    1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



25. REMOVE REAR DOOR SCUFF PLATE LH


    B270519

  1. Disengage the 4 claws, 2 guides and 2 clips, and remove the rear door scuff plate LH.



26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. Remove the rear door opening trim weatherstrip LH.

  1. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

    NOTICE:
    Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.



27. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B265187

  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B265188

  1. Remove the bolt and disconnect the floor end of the front seat outer belt assembly.



29. REMOVE CENTER PILLAR LOWER GARNISH LH


    B270537

  1. Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.



30. REMOVE CENTER PILLAR UPPER GARNISH LH


    B270539

  1. Remove the screw.

  1. Disengage the 2 clips.

  1. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.



31. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



32. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



33. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



34. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



35. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



36. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



37. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



38. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



39. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



40. REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:
Use the same procedure as for the LH side.



41. REMOVE REAR SEAT SIDE GARNISH LH


    B270545

  1. Remove the clip.

  1. Disengage the 6 claws and remove the rear seat side garnish LH.



42. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    B270553E01

  1. Using a screwdriver, disengage the 2 claws.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt and the rope hook assembly.



43. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)


    B270557

  1. Remove the bolt.

  1. Disengage the guide and remove the luggage hold belt striker assembly.



44. REMOVE TONNEAU COVER HOOK (for LH Side)


    B270561E01

  1. Using a screwdriver, disengage the 2 claws and pin, and remove the tonneau cover hook.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.



45. REMOVE TONNEAU COVER HOLDER CAP (for LH Side)


    B270574E01

  1. Using a screwdriver, disengage the claws and guide, and remove the tonneau cover holder cap.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.



46. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    B265184

  1. Remove the bolt and disconnect the floor end of the rear seat outer belt assembly.



47. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

  1. Remove the 3 screws.



  1. Disengage the 4 claws and 3 clips, and remove the deck trim side panel assembly LH.


    B270566



48. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH


    B270569

  1. Using a moulding remover, disengage the 3 claws and 2 guides, and disconnect the belt guide.



  1. Disengage the 8 clips


    B270572

  1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH and remove the roof side inner garnish assembly LH.



49. REMOVE REAR SEAT SIDE COVER RH


    B270543

  1. Disengage the 3 claws and 2 clips, and remove the rear seat side cover RH.



50. REMOVE REAR SEAT SIDE GARNISH RH

HINT:
Use the same procedure as for the LH side.



51. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure as for the LH side.



52. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure as for the LH side.



53. REMOVE TONNEAU COVER HOOK (for RH Side)


    B270563E01

  1. Using a screwdriver, disengage the 2 claws and pin, and remove the tonneau cover hook.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.



54. REMOVE TONNEAU COVER HOLDER CAP (for RH Side)

HINT:
Use the same procedure as for the LH side.



55. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    E219171E01

  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *1
    		Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



56. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



57. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



58. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



59. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY
(Click here)


60. REMOVE BACK DOOR WEATHERSTRIP

  1. Remove the back door weatherstrip.

  1. Remove the residual weatherstrip sealant from the body of the vehicle using cleaner.

    NOTICE:
    Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.



61. REMOVE MAP LIGHT ASSEMBLY

  1. Open the overhead console.



    E220652E01

  1. Disengage the 4 clips and 3 guides as shown in the illustration.

  1. Disconnect the connector and remove the map light assembly.



62. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    E189683E02

  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and remove the No. 1 room light lens.
    Text in Illustration 
    *1
    		Protective Tape



    E189687E02

  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws and disconnect the No. 1 room light housing as shown in the illustration.
    Text in Illustration 
    *1
    		Protective Tape



    E220648E01

  1. Disengage the 4 claws and disconnect the room light switch base from the No. 1 room light housing.
    Text in Illustration 
    *a
    		Room Light Switch Base



63. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


  1. w/o Rear View Monitor System:



      B269074

    1. Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.



      2. B269076

    2. Disengage the 6 claws and remove the inner rear view mirror stay holder cover.



  1. w/ Rear View Monitor System:



      B269077

    1. Disengage the 2 guides and slide the inner rear view mirror stay holder cover as shown in the illustration.



      2. B269079

    2. Disengage the 2 claws and remove the inner rear view mirror stay holder cover.



64. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    E220061

  1. Disengage the 2 guides and disconnect the rain sensor cover as shown in the illustration.

  1. Disengage the 2 claws and remove the rain sensor cover.



65. REMOVE PROTECTOR (w/ Humidity Sensor)


    E203443

  1. Disengage the 2 guides and slide the protector as shown in the illustration.

  1. Disengage the 2 claws and remove the protector.



66. REMOVE ASSIST GRIP SUB-ASSEMBLY


    B211689E01

  1. Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
    Text in Illustration 
    *1
    		Protective Tape

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 clips and remove the assist grip sub-assembly.



    B235006

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the other 3 assist grip sub-assemblies.



67. REMOVE VISOR BRACKET COVER (for LH Side)


    B233682

  1. Using a moulding remover, disengage the 4 claws and remove the visor bracket cover LH.



68. REMOVE VISOR ASSEMBLY LH


    B233712

  1. Remove the 2 screws and the visor assembly LH.



69. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



70. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



71. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

  1. Remove the sliding roof opening trim moulding.



72. REMOVE VISOR HOLDER


    B211697E01

  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the other visor holder.



73. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

  1. w/ EC Mirror:

    1. Disconnect the inner rear view mirror connector.

  1. w/ Humidity Sensor

    1. Disconnect the humidity sensor connector.

  1. w/ Rain Sensor

    1. Disconnect the rain sensor connector.

  1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

  1. Disconnect the connector from the rear pillar RH.

  1. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.



  1. Remove the 3 clips.


    B271289



    B270579

  1. Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.



74. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

  1. w/ EC Mirror:

    1. Disconnect the inner rear view mirror connector.

  1. w/ Humidity Sensor

    1. Disconnect the humidity sensor connector.

  1. w/ Rain Sensor

    1. Disconnect the rain sensor connector.

  1. Disengage the 3 clamps and disconnect the connector from the front pillar RH.

  1. Disconnect the connector from the rear pillar RH.

  1. Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.

  1. Disconnect the connector from the sliding roof drive gear assembly.



  1. Remove the 3 clips.


    B271290



    B270581

  1. Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.