PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 PARKING BRAKE CABLE CLAMP


    C158972

  1. Engage the 2 claws to install a new No. 2 parking brake cable clamp to the No. 3 parking brake cable assembly.



2. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


  1. Install the No. 3 parking brake cable assembly with the 5 bolts.


    C232726

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



    C232725E01

  1. Install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    		No. 3 Parking Brake Cable Assembly
    *2
    		Clip

    HINT:
    Be sure to engage the No. 3 parking brake cable assembly clip onto the rear disc brake cylinder assembly as shown in the illustration.



    C232727

  1. Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.



    C232743

  1. Engage the clamp to install the No. 2 parking brake cable clamp.



3. INSTALL PARKING BRAKE LEVER PROTECTOR


    C233586E02

  1. Install the parking brake lever protector to the No. 3 parking brake cable assembly.



4. INSTALL REAR FLOOR SIDE MEMBER COVER (w/ Floor Under Cover)

  1. for LH Side:

    HINT:
    Perform the following procedure when installing the No. 3 parking brake cable assembly.


    1. Install the rear floor side member cover LH with the 2 bolts, nut and 2 clips.

  1. for RH Side:

    HINT:
    Perform the following procedure when installing the No. 2 parking brake cable assembly.


    1. Install the rear floor side member cover RH with the bolt, nut and 2 clips.



5. INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR


    C232742

  1. Install the front No. 2 floor heat insulator with the 3 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



6. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


7. INSTALL NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    C232722E01

  1. Connect the No. 3 parking brake cable assembly to the No. 1 parking brake pull rod sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    		No. 1 Parking Brake Pull Rod Sub-assembly
    *2
    		No. 2 Parking Brake Cable Assembly
    *3
    		No. 3 Parking Brake Cable Assembly

  1. Connect the No. 2 parking brake cable assembly to the No. 1 parking brake pull rod sub-assembly.

    HINT:
    Perform the same procedure as for the No. 3 parking brake cable assembly.



8. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)

  1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.



    C232705

  1. Install the clip to the No. 1 parking brake cable assembly.



    C232709

  1. Bend the parking brake pedal claw.



    C232703

  1. Temporarily install the adjusting nut.



9. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)

  1. Pass the No. 1 parking brake cable assembly through the parking brake pedal assembly.



    C232708

  1. Install the clip to the No. 1 parking brake cable assembly.



    C232710

  1. Bend the parking brake pedal claw.



    C232706

  1. Temporarily install the adjusting nut.



10. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)
(Click here)


11. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)
(Click here)


12. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }