PARKING BRAKE CABLE > REMOVAL

for Preparation Click here


HINT:
  1. The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.
  2. Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.



1. REMOVE REAR WHEEL


2. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)
(Click here)


3. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)
(Click here)


4. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD)


    C232703

  1. Remove the adjusting nut.



    C232704

  1. Pull up the parking brake pedal claw.



    C232705

  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.



5. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD)


    C232706

  1. Remove the adjusting nut.



    C232707

  1. Pull up the parking brake pedal claw.



    C232708

  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.



6. REMOVE NO. 1 PARKING BRAKE PULL ROD SUB-ASSEMBLY


    C232721E01

  1. Separate the No. 3 parking brake cable assembly from the No. 1 parking brake pull rod sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    		No. 1 Parking Brake Pull Rod Sub-assembly
    *2
    		No. 2 Parking Brake Cable Assembly
    *3
    		No. 3 Parking Brake Cable Assembly

  1. Separate the No. 2 parking brake cable assembly to remove the No. 1 parking brake pull rod sub-assembly.

    HINT:
    Perform the same procedure as for the No. 3 parking brake cable assembly.



7. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


8. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR


    C232742

  1. Remove the 3 nuts and front No. 2 floor heat insulator.



9. REMOVE REAR FLOOR SIDE MEMBER COVER (w/ Floor Under Cover)


  1. for LH Side:

    HINT:
    Perform the following procedure when removing the No. 3 parking brake cable assembly.




      C232810

    1. Remove the 2 bolts, nut and clip.

    2. Disengage the clip and remove the rear floor side member cover LH.



  1. for RH Side:

    HINT:
    Perform the following procedure when removing the No. 2 parking brake cable assembly.




      C232811

    1. Remove the bolt and nut.

    2. Disengage the 2 clips and remove the rear floor side member cover RH.



10. REMOVE PARKING BRAKE LEVER PROTECTOR


    C233586E01

  1. Remove the parking brake lever protector from the No. 3 parking brake cable assembly.



11. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C232743

  1. Disengage the clamp to separate the No. 2 parking brake cable clamp.



    C232723

  1. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



    C232724E01

  1. Disconnect the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.
    Text in Illustration 
    *1
    		No. 3 Parking Brake Cable Assembly
    *2
    		Clip
    *3
    		Offset Wrench (14 mm)

    HINT:
    Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.



  1. Remove the 5 bolts and No. 3 parking brake cable assembly.


    C232726



12. REMOVE NO. 2 PARKING BRAKE CABLE CLAMP


    C158971

  1. Disengage the 2 claws to remove the No. 2 parking brake cable clamp from the No. 3 parking brake cable assembly.