POWER MIRROR CONTROL SYSTEM (w/ Memory) > OPERATION CHECK

for Preparation Click here



CHECK REMOTE CONTROL MIRROR FUNCTION

  1. Turn the power switch on (IG).

  2. With the mirror select switch set to L, check that the mirror surface moves up, down, left and right normally.

  3. With the mirror select switch set to R, check that the mirror surface moves up, down, left and right normally.


CHECK MEMORY AND REACTIVATION FUNCTION

B273330E01

HINT:
The SET, M1, M2 and M3 seat memory switches are shown in the illustration.

  1. Turn the power switch on (IG) and push the P position switch (transmission shift main switch).
    Text in Illustration 
    *A
    		for LHD
    *B
    		for RHD
    *1
    		SET Switch
    *2
    		M1 Switch
    *3
    		M2 Switch
    *4
    		M3 Switch



    2. B227715E13

  2. Check the M1 switch.

    1. Using the mirror adjust switch, turn the mirror surface to the full left position.
      Text in Illustration 
      *a
      		Turn to Left Fully

    2. Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M1 switch is pressed within 3 seconds of the SET switch is being pressed.

      NOTICE:
      1. The mirror surface position will be stored when the M1 switch is pressed after first pressing and holding the SET switch.
      2. The mirror surface position will not be stored when the SET switch and M1 switch are pressed simultaneously.
      3. The mirror surface position will not be stored when 2 or more of the memory switches are pressed simultaneously (for example, M1 and M2) after first pressing the SET switch.

    3. Using the outer mirror switch assembly, turn the mirror surface to the full right position.

    4. Press the M1 switch.

    5. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded full left position.



    3. B227716E05

  3. Check the M2 switch.

    1. Using the mirror adjust switch assembly, turn the mirror surface to the full right position.
      Text in Illustration 
      *a
      		Turn to Right Fully

    2. Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M2 switch is pressed within 3 seconds of the SET switch is being pressed.

      NOTICE:
      1. The mirror surface position will be stored when the M2 switch is pressed after first pressing and holding the SET switch.
      2. The mirror surface position will not be stored when the SET switch and M2 switch are pressed simultaneously.
      3. The mirror surface position will not be stored when 2 or more of the memory switches are pressed simultaneously (for example, M1 and M2) after first pressing the SET switch.

    3. Using the outer mirror switch assembly, turn the mirror surface to the full left position.

    4. Press the M2 switch.

    5. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded full right position.



    4. B227717E02

  4. Check the M3 switch.

    1. Using the outer mirror switch assembly, turn the mirror surface to the full upward position.
      Text in Illustration 
      *a
      		Turn Upward Fully

    2. Check that the buzzer sounds for 0.5 seconds and the seat position is memorized when the M3 switch is pressed within 3 seconds after the SET switch is being pressed.

      NOTICE:
      1. The mirror surface position will be stored when the M3 switch is pressed after first pressing and holding the SET switch.
      2. The mirror surface position will not be stored when the SET switch and M3 switch are pressed simultaneously.
      3. The mirror surface position will not be stored when 2 or more of the memory switches are pressed simultaneously (for example, M1 and M2) after first pressing the SET switch.

    3. Using the outer mirror switch assembly, turn the mirror surface to the full downward position.

    4. Press the M3 switch.

    5. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded full upward position.


CHECK POWER RETRACTABLE MIRROR FUNCTION

  1. Turn the power switch on (IG).



  2. At each outer rear view mirror assembly position, check the retractable mirror operation when operating the retractable outer mirror switch.



      B227710

    1. Move the mirrors to the driving position.

    2. Turn the retractable outer mirror switch to the retract position.

    3. Check that the right and left outer rear view mirror assemblies move from the driving position to the retracted position.



      4. B227712

    4. Move the mirrors to the driving position.

    5. Move one of the outer rear view mirror assemblies to the forward position by hand.

    6. Turn the retractable outer mirror switch to the retract position.

    7. Check that the outer rear view mirror assemblies in the forward position moves to the retracted position, and check that the other mirror moves to the retracted position.



      8. B227713

    8. Move the outer rear view mirror assemblies to the driving position.

    9. Move one of the outer rear view mirror assemblies to the retracted position by hand.

    10. Turn the retractable outer mirror switch to the retract position.

    11. Check that the outer rear view mirror assemblies in the driving position moves to the retracted position.



      12. B227711

    12. Move the mirrors to the retracted position.

    13. Turn the retractable outer mirror switch to the driving position.

    14. Check that the right and left mirrors move from the retracted position to the driving position.



      15. B227714

    15. Move the mirrors to the retracted position.

    16. Move one of the outer rear view mirror assemblies to the driving position by hand.

    17. Turn the retractable outer mirror switch to the driving position.

    18. Check that the retracted outer rear view mirror assembly moves to the driving position.

  3. Check the operation of the outer rear view mirror assembly according to retractable outer mirror switch operations and power switch condition.

    1. When the outer rear view mirror assembly is operating, turn the power switch off and check that the mirror operation stops immediately.

    2. This time, turn the power switch on (ACC) and press the retractable outer mirror switch. Check that the outer rear view mirror assembly operates in the opposite direction.

  4. Check the operation of the outer rear view mirror assembly when it is blocked by an obstacle.

    1. When the outer rear view mirror is moving to the retracted or driving position, block the outer rear view mirror assembly by hand. Check that the mirror stops moving.

    2. With the outer rear view mirror assembly stopped partway, push the retractable outer mirror switch. Check that the outer rear view mirror assembly moves in the opposite direction.


CHECK AUTO ELECTRIC RETRACT FUNCTION

  1. With the power switch off and the retractable outer mirror switch in the AUTO position, when the doors are unlocked through the entry, wireless or key-linked function, check that the outer rear view mirror assemblies move from the retracted position to the driving position, and stop in the driving position.

  2. With the power switch off, and the retractable outer mirror switch in the AUTO position, when the doors are locked through the entry, wireless or key-linked function, check that the outer rear view mirror assemblies move from the driving position to the retracted position, and stop in the retracted position.

  3. When the power switch is on (ACC) and then turned off while the retractable outer mirror switch is in AUTO position, check that both outer rear view mirror assemblies automatically move from the driving position to the retracted position.

  4. When the power switch is off and then turned on (ACC) while the retractable outer mirror switch is in the AUTO position, check that both outer rear view mirror assemblies automatically move from the retracted position to the driving position.


CHECK REVERSE SHIFT-LINKED OPERATION OF MIRRORS


    B273119E02

  1. Turn the power switch on (IG).

  2. Set the mirror select switch to L or R.
    Text in Illustration 
    *1
    		Mirror Select Switch
    *a
    		Downward

  3. Check that the mirror surface turns downward when the shift lever is moved to R.

  4. Check that the mirror surface position returns to the original position when one of the following conditions is met:

    1. Shift lever is moved to any position other than R.
    2. Mirror select switch is in the neutral position (off).
    3. Power switch is turned off.


CHECK MEMORY CALL FUNCTION

  1. Automatic memory call function check

    1. With a transmitter key recognition code registered:
      Perform a wireless door unlock operation and check that opening the driver side door causes the following:

      1. The buzzer sounds for 0.1 seconds.
      2. The front seat and outer mirror surface position automatically move to the stored positions.

      HINT:
      1. The registered transmitter key recognition code is recalled automatically.
      2. If the automatic memory call function is not operated, the buzzer will not sound.

  2. With the power switch off and the driver side door closed, press and hold the M1, M2 or M3 switch while carrying the transmitter key. The main body ECU (multiplex network body ECU) will enter transmitter key recognition code registration mode to allow a key to be linked to mirror surface memory position.

    HINT:
    If the memory switch is released before entering registration mode, the memory switch will not enter registration mode.

  3. When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds once (0.5 seconds).

  4. With the power switch off and the driver side door closed, press and hold the SET switch while carrying the transmitter key. The main body ECU (multiplex network body ECU) will enter transmitter key recognition code deletion mode.

    HINT:
    If the memory switch is released before entering deletion mode, the memory switch will not enter deletion mode.

  5. When the manual door lock switch is pressed, check that the buzzer of the position control ECU and switch assembly sounds twice (0.1 seconds each time).


EMERGENCY STOP FUNCTION

  1. While a memory call function is operating, check that any one of the following actions will stop the memory call operation: 1) pressing the SET, M1, M2 or M3 switch, 2) moving the shift lever to R, 3) moving the mirror surface manually, or 4) moving the mirror surface to the uppermost, lowermost, leftmost or rightmost position.