DTC    U1100    Lost Communication with Seat Belt Control ECU

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U1100
No communication from the seat belt control ECU continues.
  1. Seat belt control ECU branch line or connector
  2. Power source circuit of seat belt control ECU
  3. Seat belt control ECU

HINT:
This diagnosis procedure is for when DTC U1100 is output by the power management control ECU (Intelligent tester display: PM1 Gateway).


WIRING DIAGRAM


C234580E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
  2. Turn the power switch off before inspecting CAN bus lines for a ground short.
  3. After the power switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  4. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the power switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT

  1. Reconfirm DTCs.

    HINT:
    If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a V2 bus malfunction. Troubleshoot for DTC U1002 and check for malfunctions in the V2 bus.

    Result:
    Result
    		Proceed to
    U1002 is not output from power management control ECU (Intelligent tester display/PM1 Gateway)
    		A
    U1002 is output from power management control ECU (Intelligent tester display/PM1 Gateway)
    		B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


2.CHECK CAN BUS LINE FOR DISCONNECTION (SEAT BELT CONTROL ECU BRANCH LINE)

  1. Turn the power switch off.



    C150943E19

  1. Disconnect the seat belt control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    H7-1 (CANH) - H7-2 (CANL)
    		Power switch off
    		54 to 69 Ω

    Text in Illustration 
    *a
    		Front view of wire harness connector
    (to Seat Belt Control ECU)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SEAT BELT CONTROL ECU)
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

  1. Disconnect the seat belt control ECU connector.



    C210431E07

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Switch Condition
    		Specified Condition
    H6-7 (+B) - Body ground
    		Power switch off
    		11 to 14 V
    H7-8 (IG1) - Body ground
    		Power switch on (IG)
    		11 to 14 V

    Text in Illustration 
    *a
    		Front view of wire harness connector
    (to Seat Belt Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C204469E03

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    H6-8 (PGND) - Body ground
    		Always
    		Below 1 Ω

    Text in Illustration 
    *a
    		Front view of wire harness connector
    (to Seat Belt Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE SEAT BELT CONTROL ECU (Click here)