REAR POWER WINDOW SWITCH > INSPECTION

for Preparation Click here



1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Side)


    B203473E29

  1. Check the switch function.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      6 (UP) - 1 (GND)
      		Auto up or up position
      		Below 1 Ω
      7 (DOWN) - 1 (GND)
      		Auto down or down position
      		Below 1 Ω
      8 (AUTO) - 1 (GND)
      		Auto up or auto down position
      		Below 1 Ω
      6 (UP) - 1 (GND)
      		Free
      		10 kΩ or higher
      7 (DOWN) - 1 (GND)
      		Free
      		10 kΩ or higher
      8 (AUTO) - 1 (GND)
      		Free
      		10 kΩ or higher

      Text in Illustration 
      *a
      		Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for LH Side))
      If the result is not as specified, replace the rear power window regulator switch assembly (for LH side).



    B203473E32

  1. Check that the LED illuminates.

    1. Apply battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → 4 (LED)
      Battery negative (-) → 1 (GND)
      		LED illuminates

      Text in Illustration 
      *a
      		Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for LH Side))
      *b
      		LED
      If the result is not as specified, replace the rear power window regulator switch assembly (for LH side).



2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Side)


    B203473E29

  1. Check the switch function.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Switch Condition
      		Specified Condition
      6 (UP) - 1 (GND)
      		Auto up or up position
      		Below 1 Ω
      7 (DOWN) - 1 (GND)
      		Auto down or down position
      		Below 1 Ω
      8 (AUTO) - 1 (GND)
      		Auto up or auto down position
      		Below 1 Ω
      6 (UP) - 1 (GND)
      		Free
      		10 kΩ or higher
      7 (DOWN) - 1 (GND)
      		Free
      		10 kΩ or higher
      8 (AUTO) - 1 (GND)
      		Free
      		10 kΩ or higher

      Text in Illustration 
      *a
      		Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for RH Side))
      If the result is not as specified, replace the rear power window regulator switch assembly (for RH side).



    B203473E32

  1. Check that the LED illuminates.

    1. Apply battery voltage to the rear power window regulator switch assembly and check that the LED illuminates.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → 4 (LED)
      Battery negative (-) → 1 (GND)
      		LED illuminates

      Text in Illustration 
      *a
      		Component without harness connected
      (Rear Power Window Regulator Switch Assembly (for RH Side))
      *b
      		LED
      If the result is not as specified, replace the rear power window regulator switch assembly (for RH side).