FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Wireless Transmitter Memory Function does not Operate

for Preparation Click here


DESCRIPTION

With the power switch off and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch assembly while holding a seat memory switch (M1 switch, M2 switch or M3 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After the registration is completed, the answer back buzzer sounds.

NOTICE:
  1. The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
  2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).

    OK:
    CAN communication DTC is not output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK POWER DOOR LOCK CONTROL SYSTEM

  1. Check the manual lock/unlock function by using the multiplex network master switch assembly (Click here).

    OK:
    Manual lock/unlock function operates normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


3.CHECK ENTRY AND START SYSTEM (for Start Function)

  1. Check that the hybrid control system starts normally when the power switch is pressed with carrying the key and the brake pedal depressed.

    OK:
    Hybrid control system starts normally.

    Result:
    Result
    		Proceed to
    OK
    		A
    NG (w/ Entry Function)
    		B
    NG (w/o Entry Function)
    		C



B
GO TO ENTRY AND START SYSTEM (for Start Function) (Click here)

C
GO TO PUSH-BUTTON START SYSTEM (Click here)
A


4.CHECK SEAT POSITION MEMORY FUNCTION

  1. Perform a seat position memory function (Click here).

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the seat position memory function.

    NOTICE:
    1. The seat position will not be recorded if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
    2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

    OK:
    Seat position memory function operates normally.



NG
GO TO OTHER FLOW CHART (Power Seat Position is not Memorized) (Click here)
OK


5.CHECK SEAT POSITION RESTORING FUNCTION

  1. Perform a seat position restoring function (Click here).

  1. Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

    NOTICE:
    1. The seat position will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.
    2. If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.

    OK:
    Seat position restoring function operates normally.



NG
GO TO OTHER FLOW CHART (Power Seat does not Return to Memorized Position) (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR COURTESY SWITCH)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Connection
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    FR Door Courtesy*1
    		Front door courtesy light switch assembly signal / ON or OFF
    		ON: Driver door open
    OFF: Driver door closed
    		-
    FL Door Courtesy*2
    		Front door courtesy light switch assembly signal / ON or OFF
    		ON: Driver door open
    OFF: Driver door closed
    		-

    1. *1: for RHD
    2. *2: for LHD

    OK:
    ON or OFF appears on the screen according to the driver door condition.



NG
GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit) (Click here)
OK


7.CHECK MEMORY CALL REGISTRATION FUNCTION

  1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.

    1. Power switch is off
    2. Press and hold the M1, M2 or M3 seat memory switch
    3. Driver door closed
    4. Carry the key

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (Click here).

OK:
Buzzer sounds normally.



NG
Go to step 10
OK


8.READ VALUE USING INTELLIGENT TESTER (MEMORY CALL REGISTRATION)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Mem SW No. w/KeyID1
    		Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID1
    MEM SW1: M1 switch linked with key ID1
    MEM SW2: M2 switch linked with key ID1
    MEM SW3: M3 switch linked with key ID1
    		-
    Mem SW No. w/KeyID2
    		Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID2
    MEM SW1: M1 switch linked with key ID2
    MEM SW2: M2 switch linked with key ID2
    MEM SW3: M3 switch linked with key ID2
    		-
    Mem SW No. w/KeyID3
    		Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID3
    MEM SW1: M1 switch linked with key ID3
    MEM SW2: M2 switch linked with key ID3
    MEM SW3: M3 switch linked with key ID3
    		-
    Mem SW No. w/KeyID4
    		Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID4
    MEM SW1: M1 switch linked with key ID4
    MEM SW2: M2 switch linked with key ID4
    MEM SW3: M3 switch linked with key ID4
    		-
    Mem SW No. w/KeyID5
    		Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID5
    MEM SW1: M1 switch linked with key ID5
    MEM SW2: M2 switch linked with key ID5
    MEM SW3: M3 switch linked with key ID5
    		-
    Mem SW No. w/KeyID6
    		Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID6
    MEM SW1: M1 switch linked with key ID6
    MEM SW2: M2 switch linked with key ID6
    MEM SW3: M3 switch linked with key ID6
    		-
    Mem SW No. w/KeyID7
    		Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3
    		NONE: No switches linked with key ID7
    MEM SW1: M1 switch linked with key ID7
    MEM SW2: M2 switch linked with key ID7
    MEM SW3: M3 switch linked with key ID7
    		-

    OK:
    On the intelligent tester display, it is confirmed that the memory call has been registered.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


9.CHECK MEMORY CALL FUNCTION

  1. Turn the power switch off.

  1. Close and lock all doors.

  1. Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle with holding the memory call registered key.

  1. Open the driver door and check that the driver seat moves to the memorized position (Click here).

    OK:
    Driver seat moves to the memorized position.



NG
GO TO OTHER FLOW CHART (Wireless-linked Return Function does not Operate) (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

10.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


11.CHECK MEMORY CALL REGISTRATION FUNCTION

  1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.

    1. Power switch is off
    2. Press and hold the M1, M2 or M3 seat memory switch
    3. Driver door closed
    4. Carry the key

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (Click here).

OK:
Buzzer sounds normally.



NG
Go to step 12
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) 

12.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

  1. Replace the position control ECU and switch assembly (Click here).


NEXT


13.CHECK MEMORY CALL REGISTRATION FUNCTION

  1. When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.

    1. Power switch is off
    2. Press and hold the M1, M2 or M3 seat memory switch
    3. Driver door closed
    4. Carry the key

  1. Check that the buzzer sounds for 0.5 seconds to indicate the completion of the memory call registration function (Click here).

OK:
Buzzer sounds normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)