REAR SEAT ASSEMBLY > REASSEMBLY

for Preparation Click here



1. INSTALL REAR SEATBACK LOCK ASSEMBLY LH


    B270656

  1. Install the rear seatback lock assembly LH with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



2. INSTALL NO. 2 REAR SEATBACK EDGE PROTECTOR

  1. Clean the installation surface of the rear seatback frame sub-assembly LH.



  1. Attach the 4 pieces of double-sided tape and install the No. 2 rear seatback edge protector to the rear seatback frame sub-assembly LH.


    B273429E01


    Text in Illustration 
    *1
    		Double-sided Tape
    		-
    		-
    *a
    		No. 2 Rear Seatback Edge Protector
    		*b
    		Front Side of Rear Seatback Frame LH
    *c
    		Upper Limit of Headrest Support Bracket
    		*d
    		Insert
    *e
    		Reference Line
    		*f
    		Back Side of Rear Seatback Frame LH



3. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


  1. Insert the rod of the rear seatback lock assembly LH to the rear seat lock control lever sub-assembly LH as shown in the illustration.


    B271744



    B270650

  1. Engage the guide.

  1. Install the rear seat lock control lever sub-assembly LH with the 2 screws.



4. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH


    B270660

  1. Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



5. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH

  1. Temporarily install the separate type rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.



    B270649

  1. Engage the 4 claws to install the 2 rear seat headrest supports.



    B271742

  1. Engage the 2 hooks.



    B270647

  1. Engage the 8 hooks.

  1. Install 9 new clips to the separate type rear seatback cover LH.



    B270646E01

  1. Engage the 9 clips.
    Text in Illustration 
    *1
    		Fastener

  1. Engage the fastener.



    B270645

  1. Install the separate type rear seatback cover with pad LH with 2 new clips.



6. INSTALL REAR SEATBACK COVER LH


    B270642

  1. Engage the 4 claws to install the rear seatback cover LH.



7. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE LH


    B270644

  1. Engage the 5 claws.

  1. Install the rear seatback lock control lever base LH with the screw.



8. INSTALL REAR SEATBACK LOCK STRIKER COVER LH


    B270643

  1. Engage the 2 guides and claw to install the rear seatback lock striker cover LH.



9. INSTALL REAR SEATBACK LOCK ASSEMBLY RH


    B270641

  1. Install the rear seatback lock assembly RH with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }



10. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY


    B265193E01

  1. Install the rear center seat outer belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    Text in Illustration 
    *1
    		Protruding Part

    NOTICE:
    Do not allow the rear center seat outer belt assembly to overlap the protruding part of the rear seatback frame.



11. INSTALL REAR SEATBACK EDGE PROTECTOR

  1. Clean the installation surface of the rear seatback frame sub-assembly RH.



  1. Attach the 12 pieces of double-sided tape and install the rear seatback edge protector to the rear seatback frame sub-assembly RH.


    B273430E01


    Text in Illustration 
    *1
    		Double-sided Tape
    		-
    		-
    *a
    		Rear Seatback Edge Protector
    		*b
    		Front Side of Rear Seatback Frame RH
    *c
    		Upper Limit of Headrest Support Bracket
    		*d
    		Insert
    *e
    		Reference Line
    		*f
    		Bask Side of Rear Seatback Frame RH



12. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


  1. Insert the rod of the rear seatback lock assembly RH to the rear seat lock control lever sub-assembly RH as shown in the illustration.


    B271748



    B270639

  1. Engage the guide.

  1. Install the rear seat lock control lever sub-assembly RH.



13. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH


    B275404

  1. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 9 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B275406

  1. Engage the 2 hooks.



14. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH

  1. Temporarily install the separate type rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.



    B270634

  1. Engage the 4 claws to install the 2 rear seat center headrest supports.



    B270636

  1. Engage the 4 claws to install the 2 rear seat headrest supports.



    B270632

  1. Engage the 4 hooks.



    B270631

  1. Engage the 10 hooks.

  1. Install 9 new clips to the separate type rear seatback cover RH.



    B270629

  1. Engage the 9 clips.



    B270628

  1. Install the separate type rear seatback cover with pad RH with 3 new clips.



15. INSTALL REAR SEATBACK COVER RH


    B270627

  1. Engage the 4 claws to install the rear seatback cover RH.

  1. w/ Rear Seatback Cover:

    1. Install the rear seatback cover RH.

      HINT:
      Use the same procedure for the LH side and RH side.



16. INSTALL REAR SEAT SHOULDER BELT COVER


    B270626

  1. Engage the 4 claws to install the rear seat shoulder belt cover.



17. INSTALL SEAT BELT ANCHOR COVER CAP


    B270625

  1. Engage the 2 claws to install the seat belt anchor cover cap.



18. INSTALL REAR SEATBACK LOCK CONTROL LEVER BASE RH


    B270624

  1. Engage the 5 claws.

  1. Install the rear seatback lock control lever base RH with the screw.



19. INSTALL REAR SEATBACK LOCK STRIKER COVER RH


    B270623

  1. Engage the 2 guides and claw to install the rear seatback lock striker cover RH.



20. INSTALL BENCH TYPE REAR SEAT CUSHION COVER


  1. Using hog ring pliers, install 24 new hog rings.


    B270666



    B270664

  1. Using hog ring pliers, install 22 new hog rings.



    B270662

  1. Using hog ring pliers, install the bench type rear seat cushion cover to the bench type rear seat cushion pad with 21 new hog rings.