POWER MIRROR CONTROL SYSTEM (w/ Memory) > Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

When the mirror adjust switch is operated, the main body ECU (multiplex network body ECU) detects the switch operation and sends the mirror adjust switch signal to the outer mirror control ECU assembly (front passenger side) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (front passenger side) operates the vertical and horizontal mirror motors, which are built into the outer mirror actuator assembly (front passenger side), to adjust the mirror surface position.

WIRING DIAGRAM


B236440E13


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION SYSTEM

  1. Use the intelligent tester to check if the CAN communication system is functioning normally (Click here).

    OK:
    CAN communication DTC is not output.



NG
GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH ASSEMBLY)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    		Measurement Item/Range
    		Normal Condition
    		Diagnostic Note
    Mirror Selection SW (R)
    		Mirror select switch signal for RH mirror / ON or OFF
    		ON: Mirror select switch in R position
    OFF: Mirror select switch off or in L position
    		*1
    Mirror Selection SW (L)
    		Mirror select switch signal for LH mirror / ON or OFF
    		ON: Mirror select switch in L position
    OFF: Mirror select switch off or in R position
    		*2
    Mirror Position SW (R)
    		Mirror adjust switch signal (Right) / ON or OFF
    		ON: Mirror adjust switch pressed right
    OFF: Mirror adjust switch not pressed right
    		Check with the mirror select switch in the R position*1
    Check with the mirror select switch in the L position*2
    Mirror Position SW (L)
    		Mirror adjust switch signal (Left) / ON or OFF
    		ON: Mirror adjust switch pressed left
    OFF: Mirror adjust switch not pressed left
    		Check with the mirror select switch in the R position*1
    Check with the mirror select switch in the L position*2
    Mirror Position SW (Up)
    		Mirror adjust switch signal (Up) / ON or OFF
    		ON: Mirror adjust switch pressed up
    OFF: Mirror adjust switch not pressed up
    		Check with the mirror select switch in the R position*1
    Check with the mirror select switch in the L position*2
    Mirror Position SW (Dwn)
    		Mirror adjust switch signal (Down) / ON or OFF
    		ON: Mirror adjust switch pressed down
    OFF: Mirror adjust switch not pressed down
    		Check with the mirror select switch in the R position*1
    Check with the mirror select switch in the L position*2

    1. *1: for LHD
    2. *2: for RHD

    OK:
    On the intelligent tester screen, ON or OFF is displayed for each item according to the table above.



NG
Go to step 5
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)

  1. Enter the following menus: Body / Mirror R*1 or Mirror L*2 / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    1. *1: for LHD
    2. *2: for RHD

    Mirror R / Mirror L 
    Tester Display
    		Test Part
    		Control Range
    		Diagnostic Note
    Mirror Up/Down
    		Mirror vertical operation
    		Up / Down
    1. Operate with power switch on (IG) and the vehicle stopped.
    2. This test activates the mirror up or down.
    3. This operation can be confirmed by watching the mirror move in the desired direction.
    Mirror Right/Left
    		Mirror horizontal operation
    		Right / Left
    1. Operate with power switch on (IG) and the vehicle stopped.
    2. This test activates the mirror right or left.
    3. This operation can be confirmed by watching the mirror move in the desired direction.

    OK:
    Power mirror operation is normal.



NG
Go to step 4
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER SIDE) (Click here)  

4.INSPECT OUTER MIRROR ACTUATOR ASSEMBLY RH


  1. for LHD:



      B199930E09

    1. Remove the outer rear view mirror assembly RH (Click here).

    2. Apply auxiliary battery voltage and check the operation of the outer rear view mirror assembly RH.

      OK:
      Measurement Condition
      		Specified Condition
      Auxiliary battery positive (+) → Terminal z7-1 (RMVR)
      Auxiliary battery negative (-) → Terminal z7-10 (RM+R)
      		Turns upward
      Auxiliary battery negative (-) → Terminal z7-1 (RMVR)
      Auxiliary battery positive (+) → Terminal z7-10 (RM+R)
      		Turns downward
      Auxiliary battery positive (+) → Terminal z7-9 (RMHR)
      Auxiliary battery negative (-) → Terminal z7-10 (RM+R)
      		Turns left
      Auxiliary battery negative (-) → Terminal z7-9 (RMHR)
      Auxiliary battery positive (+) → Terminal z7-10 (RM+R)
      		Turns right

      Text in Illustration 
      *a
      		Component without harness connected
      (Outer Mirror Actuator Assembly RH)



  1. for RHD:



      B199931E08

    1. Remove the outer rear view mirror assembly LH (Click here).

    2. Apply auxiliary battery voltage and check the operation of the outer rear view mirror assembly LH.

      OK:
      Measurement Condition
      		Specified Condition
      Auxiliary battery positive (+) → Terminal z6-1 (LMVR)
      Auxiliary battery negative (-) → Terminal z6-10 (LM+R)
      		Turns upward
      Auxiliary battery negative (-) → Terminal z6-1 (LMVR)
      Auxiliary battery positive (+) → Terminal z6-10 (LM+R)
      		Turns downward
      Auxiliary battery positive (+) → Terminal z6-9 (LMHR)
      Auxiliary battery negative (-) → Terminal z6-10 (LM+R)
      		Turns left
      Auxiliary battery negative (-) → Terminal z6-9 (LMHR)
      Auxiliary battery positive (+) → Terminal z6-10 (LM+R)
      		Turns right

      Text in Illustration 
      *a
      		Component without harness connected
      (Outer Mirror Actuator Assembly LH)



NG
REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (FRONT PASSENGER SIDE) (Click here)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER SIDE) (Click here)  

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY


    B273168E01

  1. Remove the outer mirror switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    H136-8 (M+) - H136-6 (E)
    		Mirror adjust switch pressed up
    		90 to 110 Ω
    Mirror adjust switch pressed down
    		437 to 503 Ω
    Mirror adjust switch pressed left
    		744 to 856 Ω
    Mirror adjust switch pressed right
    		225 to 275 Ω
    H136-3 (MSW) - H136-6 (E)
    		Mirror select switch R
    		Below 10 Ω
    Mirror select switch L
    		90 to 110 Ω
    Mirror select switch off
    		10 kΩ or higher

    Text in Illustration 
    *1
    		Mirror Adjust Switch
    *2
    		Mirror Select Switch
    *a
    		Component without harness connected
    (Outer Mirror Switch Assembly)



NG
REPLACE OUTER MIRROR SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)

  1. Disconnect the H136 connector from the outer mirror switch assembly.

  1. Disconnect the H17 connector from the main body ECU (multiplex network body ECU).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    H136-6 (E) - H17-15 (MIRE)
    		Always
    		Below 1 Ω
    H136-8 (M+) - H17-13 (MIRB)
    		Always
    		Below 1 Ω
    H136-3 (MSW) - H17-14 (MIRS)
    		Always
    		Below 1 Ω
    H136-6 (E) - Body ground
    		Always
    		10 kΩ or higher
    H136-8 (M+) - Body ground
    		Always
    		10 kΩ or higher
    H136-3 (MSW) - Body ground
    		Always
    		10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)