HEADLIGHT LEVELING ECU (for LHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (Click here).



2. REMOVE REAR NO. 2 FLOOR BOARD

  1. Remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX

  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD

  1. Remove the rear No. 3 floor board.



5. REMOVE DECK FLOOR BOX RH


    B270546

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box RH.



6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    B270547

  1. Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side (Click here).



9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side (Click here).



10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and LH side (Click here).



11. REMOVE INSTRUMENT SIDE PANEL RH


    B269869

  1. Using a moulding remover, disengage the 3 claws, clip and 4 guides, and remove the instrument side panel RH.

  1. Disconnect the connector.



12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B269873

  1. Disengage the 2 clips, claw and guide.

  1. Disengage the clamp.

  1. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.



13. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:
When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.

  1. Check that the power switch is off.

  1. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



    B252846

  1. Remove the 3 bolts.



    B252847

  1. Disengage the 6 claws and 2 guides to separate the lower No. 2 instrument panel airbag assembly.



    B252862E01

  1. Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.
    Text in Illustration 
    *1
    		Protective Tape

  1. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



14. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B269875

  1. Remove the 4 screws <C>.

  1. Disengage the 5 claws.

  1. Disengage the clamp.

  1. Disconnect the connector and remove the glove compartment door assembly.



15. REMOVE HEADLIGHT LEVELING ECU ASSEMBLY


    E220336

  1. Disconnect the connector.

  1. Remove the nut.

  1. Disengage the guide and remove the headlight leveling ECU assembly.