REAR COIL SPRING > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. REMOVE REAR WHEEL


2. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)


    E220665E01

  1. Disengage the clamp.

  1. Disconnect the connector.
    Text in Illustration 
    *1
    		Clamp
    *2
    		Guide

  1. Remove the 2 bolts.

  1. Disengage the 2 guides and remove the rear height control sensor sub-assembly.

    NOTICE:
    Do not drop the rear height control sensor sub-assembly. If it is dropped, replace it with a new one.



3. REMOVE REAR SUSPENSION ARM COVER


    C234168

  1. Remove the 2 bolts and disengage the 2 claws to remove the rear suspension arm cover from the rear No. 2 suspension arm assembly.



4. REMOVE REAR FLOOR SIDE MEMBER COVER (w/ Floor Under Cover)


  1. for LH Side:



      C232810

    1. Remove the 2 bolts, nut and clip.

    2. Disengage the clip and remove the rear floor side member cover LH.



  1. for RH Side:



      C232811

    1. Remove the bolt and nut.

    2. Disengage the 2 clips and remove the rear floor side member cover RH.



5. REMOVE REAR SUSPENSION MEMBER BRACE


    C232807

  1. Remove the 3 bolts and rear suspension member brace LH from the rear suspension member sub-assembly.



6. REMOVE REAR STABILIZER LINK ASSEMBLY


    C211883

  1. Remove the nut (A) and separate the rear stabilizer link assembly LH from the rear stabilizer bar.
    Text in Illustration 
    V100135
    		Nut (A)
    V100136
    		Nut (B)

    HINT:
    If the ball joint turns together with the nut, use a hexagon socket wrench to hold the stud bolt.

  1. Remove the nut (B), rear stabilizer link assembly LH and 2 rear stabilizer cushions.



7. REMOVE REAR COIL SPRING


    C234176E01

  1. Support the rear axle assembly with a jack using a wooden block as shown in the illustration.
    Text in Illustration 
    *1
    		Wooden Block
    *2
    		Jack

    NOTICE:
    Keep supporting the rear axle assembly with a jack until the installation of the rear coil spring has been completed.



    C232806E01

  1. Support the rear No. 2 suspension arm assembly using a jack and wooden block.
    Text in Illustration 
    *1
    		Wooden Block
    *2
    		Jack
    V100135
    		Bolt (A)
    V100136
    		Bolt (B)
    V100137
    		Bolt (C)

    NOTICE:
    1. When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
    2. Make sure to perform this operation with the vehicle kept as low as possible.

  1. Loosen the bolt (A).

    NOTICE:
    1. Since a stopper nut is used, turn the bolt.
    2. Do not remove the bolt.

  1. Remove the bolt (B) and nut, and separate the rear No. 2 suspension arm assembly from the rear axle assembly.

    NOTICE:
    Since a stopper nut is used, turn the bolt.

  1. Remove the bolt (C) and nut, and then slowly lower the rear No. 2 suspension arm assembly, and remove the rear coil spring.

    NOTICE:
    Since a stopper nut is used, turn the bolt.



8. REMOVE REAR UPPER COIL SPRING INSULATOR

  1. Remove the rear upper coil spring insulator.



9. REMOVE REAR LOWER COIL SPRING INSULATOR

  1. Remove the rear lower coil spring insulator.