DTC    B27A8    Open in Outside Luggage Compartment Electrical Key Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage). For the electrical key antenna (outside luggage) to detect when the key is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (between terminals CLG8 and CLG5, or terminals CG8B and CLGB).

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B27A8
An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB) (1 trip detection logic*).
  1. Harness or connector
  2. Electrical key antenna (outside luggage)
  3. Certification ECU (smart key ECU assembly)
Any time
  1. *: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Entry lock/unlock operation cannot be performed for back door
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
B27A8
Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM


B249998E08


INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
  5. Electrical key antenna (outside luggage) has an antenna coil between CLG5 and CLGB terminals.

1.CHECK CONNECTOR CONNECTION

  1. Turn the power switch off.

  1. Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

  1. Disconnect the H2 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the Q11 electrical key antenna (outside luggage) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    H2-19 (CLG8) - Q11-1 (CLG5)
    		Always
    		Below 1 Ω
    H2-20 (CG8B) - Q11-2 (CLGB)
    		Always
    		Below 1 Ω
    H2-19 (CLG8) or Q11-1 (CLG5) - Body ground
    		Always
    		10 kΩ or higher
    H2-20 (CG8B) or Q11-2 (CLGB) - Body ground
    		Always
    		10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)


    B226391E03

  1. Remove the electrical key antenna (outside luggage) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    1 (CLG5) - 2 (CLGB)
    		Always
    		Below 1 Ω



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK


4.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.


NEXT


5.CLEAR DTC

  1. Clear the DTCs (Click here).


NEXT


6.CHECK FOR DTC

  1. Check for DTCs (Click here).

    OK:
    DTC B27A8 is not output.



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)