REAR SEAT INNER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR SEAT INNER BELT ASSEMBLY (w/o Seat Heater System)


    B265180E01

  1. Install the rear seat inner belt assembly with the bolt.
    Text in Illustration 
    *1
    		Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Install the rear seat inner belt assembly with the arrow on the anchor part facing the front of the vehicle.
    2. Do not allow the anchor part of the rear seat inner belt assembly to overlap the protruding parts of the floor panel.



2. INSTALL REAR SEAT INNER BELT ASSEMBLY (w/ Seat Heater System)


    B265195E01

  1. Install the rear seat inner belt assembly with the bolt.
    Text in Illustration 
    *1
    		Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Install the rear seat inner belt assembly with the arrow on the anchor part facing the front of the vehicle.
    2. Do not allow the anchor part of the rear seat inner belt assembly to overlap the protruding parts of the floor panel.

  1. Engage the 2 clamps.

  1. Connect the connector.



3. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (w/o Seat Heater System)


    B265182E01

  1. Install the rear seat inner with center belt assembly LH with the bolt.
    Text in Illustration 
    *1
    		Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Install the rear seat inner belt assembly with the arrow on the anchor part facing the front of the vehicle.
    2. Do not allow the anchor part of the rear seat inner belt assembly to overlap the protruding parts of the floor panel.



4. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (w/ Seat Heater System)


    B265197E01

  1. Install the rear seat inner with center belt assembly LH with the bolt.
    Text in Illustration 
    *1
    		Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Install the rear seat inner belt assembly with the arrow on the anchor part facing the front of the vehicle.
    2. Do not allow the anchor part of the rear seat inner belt assembly to overlap the protruding parts of floor panel.

  1. Engage the 2 clamps.

  1. Connect the 2 connectors.



5. INSTALL REAR SEAT CUSHION LOCK HOOK


    B274370

  1. Engage the claw to install a new rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure the LH side and RH side.



6. INSTALL REAR SEAT CUSHION ASSEMBLY

  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.



    B274151

  1. Pass the rear center seat outer belt assembly through the rear seat cushion assembly.

  1. Install the rear center seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B275285

  1. Engage the guide as shown in the illustration.



  1. Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.


    B274150E01


    Text in Illustration 
    *1
    		Rear Seat Inner Belt Assembly
    		*2
    		Rear Seat Inner with Center Belt Assembly LH



    B274367

  1. Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.