REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here

1. Temporarily install the rear seat outer belt assembly.
   

2. Install the bolt <C>.
   

   Torque:

   7.5 N*m{ 77 kgf*cm , 66 in.*lbf }

3. Install the rear seat outer belt assembly with the bolt <B>.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

4. Install the shoulder anchor of the rear seat outer belt assembly with the bolt <A>.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

1. Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish LH.
   

2. Engage the 8 clips to install the roof side inner garnish assembly LH.
   

3. Engage the 2 guides.
   

4. Engage the 3 claws to connect the belt guide.
   

1. Engage the 4 claws and 3 clips.
   

2. Install the deck trim side panel assembly LH with the 3 screw.
   

1. Connect the floor end of the rear seat outer belt assembly with the bolt.
   

   Text in Illustration 

   *1	Protruding Part

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

   NOTICE:

   Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding parts of the floor panel.

1. Connect the connector.
   

2. Engage the claw to install the No. 2 room light assembly.
   

1. Engage the guide.
   

2. Engage the claw to install the tonneau cover holder cap.
   

1. Engage the 2 claws and pin to install the tonneau cover hook.
   

1. Engage the guide.
   

2. Install the luggage hold belt striker assembly with the bolt.
   

1. Install the rope hook assembly with the bolt.
   

2. Engage the 2 claws.
   

1. Engage the 6 claws.
   

2. Install the rear seat side garnish LH with the clip.
   

1. Engage the 3 claws and 2 clips to install the rear seat side cover RH.
   

1. Engage the 4 clips to install the rear deck trim cover.
   

1. Engage the 2 guides (B).
   

2. Engage the 2 claws and guide (A) to install the deck trim service hole cover.
   

1. Engage the 2 claws and 2 clips.
   

2. Install the rear No. 1 floor board with the bolt.
   

1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.
   

1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.
   

1. Install the tonneau cover assembly.
   

1. Engage the 6 guides.
   

2. Install the deck floor box LH with the clip.
   

1. Install the rear No. 4 floor board.
   

1. Engage the 2 clips and 3 guides to install the rear No. 4 floor board.
   

1. Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.
   

1. Engage the 6 guides.
   

2. Install the deck floor box RH with the clip.
   

1. Install the rear No. 3 floor board.
   

1. Install the rear deck floor box.
   

1. Install the rear No. 2 floor board.
   

1. Place the rear seatback assembly LH in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Install the rear seatback assembly LH with the 2 bolts.
   

   Torque:

   37 N*m{ 375 kgf*cm , 27 ft.*lbf }

3. Engage the fastener to connect the rear No. 2 floor board sub-assembly.
   

1. Place the rear seatback assembly RH in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Install the rear seatback assembly RH with the 2 bolts.
   

   Torque:

   37 N*m{ 375 kgf*cm , 27 ft.*lbf }

3. Engage the fastener to connect the rear No. 1 floor board sub-assembly.
   

1. Engage the claw to install a new rear seat cushion lock hook.
   

   NOTICE:

   Rear seat cushion lock hooks must not be reused.

   HINT:

   Use the same procedure the LH side and RH side.

1. Place the rear seat cushion assembly in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Pass the rear center seat outer belt assembly through the rear seat cushion assembly.
   

3. Install the rear center seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

4. Engage the guide as shown in the illustration.
   

5. Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.
   
   

   
   
   
   
   

   Text in Illustration 

   *1

   Rear Seat Inner Belt Assembly

   *2

   Rear Seat Inner with Center Belt Assembly LH

6. Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.
   

7. Confirm that the seat cushion is firmly installed.
   

   NOTICE:

   When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

1. Engage the 4 claws, 2 guides and 2 clips to install the rear door scuff plate LH.