REAR CENTER SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here

1. Install the rear center seat outer belt assembly with the nut.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

   Text in Illustration 

   *1	Protruding Part

   NOTICE:

   Do not allow the rear center seat outer belt assembly to overlap the protruding part of the rear seatback frame.

1. Clean the installation surface of the rear seatback frame sub-assembly RH.
   

2. Attach the 12 pieces of double-sided tape and install the rear seatback edge protector to the rear seatback frame sub-assembly RH.
   
   

   
   
   
   
   

   Text in Illustration 

   *1	Double-sided Tape	-	-
   *a	Rear Seatback Edge Protector	*b	Front Side of Rear Seatback Frame RH
   *c	Upper Limit of Headrest Support Bracket	*d	Insert
   *e	Reference Line	*f	Bask Side of Rear Seatback Frame RH

1. Temporarily install the separate type rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.
   

2. Engage the 4 claws to install the 2 rear seat center headrest supports.
   

3. Engage the 4 claws to install the 2 rear seat headrest supports.
   

4. Engage the 4 hooks.
   

5. Engage the 10 hooks.
   

6. Install 9 new clips to the separate type rear seatback cover RH.
   

7. Engage the 9 clips.
   

8. Install the separate type rear seatback cover with pad RH with 3 new clips.
   

1. Engage the 4 claws to install the rear seatback cover RH.
   

2. w/ Rear Seatback Cover:
   
   

   1. Install the rear seatback cover RH.
      

      HINT:

      Use the same procedure for the LH side and RH side.

1. Engage the 4 claws to install the rear seat shoulder belt cover.
   

1. Engage the 2 claws to install the seat belt anchor cover cap.
   

1. Engage the 5 claws.
   

2. Install the rear seatback lock control lever base RH with the screw.
   

1. Engage the 2 guides and claw to install the rear seatback lock striker cover RH.
   

1. Place the rear seatback assembly RH in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Install the rear seatback assembly RH with the 2 bolts.
   

   Torque:

   37 N*m{ 375 kgf*cm , 27 ft.*lbf }

3. Engage the fastener to connect the rear No. 1 floor board sub-assembly.
   

1. Engage the claw to install a new rear seat cushion lock hook.
   

   NOTICE:

   Rear seat cushion lock hooks must not be reused.

   HINT:

   Use the same procedure the LH side and RH side.

1. Place the rear seat cushion assembly in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Pass the rear center seat outer belt assembly through the rear seat cushion assembly.
   

3. Install the rear center seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

4. Engage the guide as shown in the illustration.
   

5. Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.
   
   

   
   
   
   
   

   Text in Illustration 

   *1

   Rear Seat Inner Belt Assembly

   *2

   Rear Seat Inner with Center Belt Assembly LH

6. Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.
   

7. Confirm that the seat cushion is firmly installed.
   

   NOTICE:

   When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.