Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B1206    P/W Master Switch Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is stored when LIN communication between the multiplex network master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.
DTC Detection Condition
Trouble Area
B1206
No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Multiplex network master switch assembly
  2. Main body ECU (multiplex network body ECU)
  3. Instrument panel junction block assembly
  4. Wire harness or connector
  5. D FR DOOR fuse

WIRING DIAGRAM


B220667E56


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When using the intelligent tester to troubleshoot with the power switch off:
    Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

1.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Remove the instrument panel junction block assembly (Click here).


    B217444E15

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    This inspection is to check the LIN line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).


    Standard Resistance:

    Tester Connection
    		Condition
    		Specified Condition
    2A-27 (LIN2) - MB-16 (LIN2)
    		Always
    		Below 1 Ω
    2A-27 (LIN2) - Body ground
    		Always
    		10 kΩ or higher


    Text in Illustration 
    *a
    		Component without harness connected
    (Instrument Panel Junction Block Assembly)
    		*b
    		Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MULTIPLEX NETWORK MASTER SWITCH)

  1. Disconnect the K5*1 or J9*2 multiplex network master switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    2A-27 (LIN2) - K5-17 (LIN1)*1
    2A-27 (LIN2) - J9-17 (LIN1)*2
    		Always
    		Below 1 Ω
    2A-27 (LIN2) - Body ground
    		Always
    		10 kΩ or higher

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY, BODY GROUND)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    K5-11 (B) - K5-12 (GND)*1
    J9-11 (B) - J9-12 (GND)*2
    		Power switch off
    		11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    K5-12 (GND) - Body ground*1
    J9-12 (GND) - Body ground*2
    		Always
    		Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

  1. Replace the multiplex network master switch assembly (Click here).


NEXT


5.CHECK DTC OUTPUT

  1. Clear the DTC (Click here).

  1. Recheck for DTCs.

    OK:
    DTC B1206 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (MULTIPLEX NETWORK MASTER SWITCH WAS DEFECTIVE)