Home › Audio/Visual/Telematics › NAVIGATION / MULTI INFO DISPLAY › HARD DISK DRIVE

HARD DISK DRIVE > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work (Click here).



2. REMOVE REAR NO. 2 FLOOR BOARD

  1. Remove the rear No. 2 floor board.



3. REMOVE REAR DECK FLOOR BOX

  1. Remove the rear deck floor box.



4. REMOVE REAR NO. 3 FLOOR BOARD

  1. Remove the rear No. 3 floor board.



5. REMOVE DECK FLOOR BOX RH


    B270546

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box RH.



6. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    B270547

  1. Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.



7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for Metal Finish Panel and Urethane Panel)


    B269877

  1. Disengage the 5 clips and remove the No. 3 instrument cluster finish panel garnish.



9. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for Wood Panel and Bamboo Panel)


    B271369

  1. Disengage the 4 clips and remove the No. 3 instrument cluster finish panel garnish.



10. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

  1. Open the glove compartment door.



    B271366

  1. Using a moulding remover, disengage the 7 claws and 4 guides, and remove the lower center instrument panel finish panel as shown in the illustration.



11. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH


    B269919

  1. Disengage the 5 claws, clip and 2 guides, and remove the upper No. 2 console panel garnish.



12. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH


    B269921

  1. Disengage the 4 claws, clip and 3 guides, and remove the upper No. 1 console panel garnish.



13. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. Open the console compartment door.



    B269923

  1. Using a moulding remover, disengage the 12 claws.

  1. Disengage the clamp.

  1. Disconnect each connector and remove the upper console panel sub-assembly.



14. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B269927

  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



15. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    B269931

  1. Disengage the 6 claws and 2 guides.

  1. Disengage the clamp.

  1. Disconnect each connector and remove the integration control and panel assembly.



16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E220731

  1. Disengage the 7 claws and remove the air conditioning control assembly as shown in the illustration.

  1. Disconnect the connector.



17. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET


    E220085

  1. Remove the 4 bolts.

  1. Pull the radio receiver assembly with bracket toward the rear of the vehicle.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.



18. REMOVE DISPLAY AND NAVIGATION MODULE DISPLAY ASSEMBLY WITH BRACKET


    E220530

  1. Remove the 4 bolts.

  1. Disconnect each connector and remove the display and navigation module display assembly with bracket.



19. REMOVE HARD DISK DRIVE (for Two Screw Type)


    E220104

  1. Remove the 2 screws.



    E220105E01

  1. Using a screwdriver, pull out the hard disk drive in the direction shown by the arrow in the illustration to remove it.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.



20. REMOVE HARD DISK DRIVE (for One Screw Type)


    E220107

  1. Remove the screw.



    E220108E01

  1. Using a screwdriver, pull out the hard disk drive in the direction shown by the arrow in the illustration to remove it.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.