FUEL LID OPENER MOTOR ASSEMBLY > INSTALLATION

for Preparation Click here

1. Install the fuel lid with motor lock assembly with the bolt.
   

   Torque:

   5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

2. Engage the 2 claws.
   

3. Connect the connector.
   

1. Temporarily install the screw.
   

   Text in Illustration 

   *1

   Screw

   NOTICE:

   Do not touch the speaker cone.

2. Install the No. 1 speaker assembly with box with the screw and 3 bolts.
   

   HINT:

   Install the screw and bolts in the order shown in the illustration.

3. Connect the connector.
   

1. Engage the 4 claws and 3 clips.
   

2. Install the deck trim side panel assembly LH with the 3 screw.
   

1. Engage the guide.
   

2. Engage the claw to install the tonneau cover holder cap.
   

1. Engage the 2 claws and pin to install the tonneau cover hook.
   

1. Engage the guide.
   

2. Install the luggage hold belt striker assembly with the bolt.
   

1. Install the rope hook assembly with the bolt.
   

2. Engage the 2 claws.
   

1. Engage the 6 claws.
   

2. Install the rear seat side garnish LH with the clip.
   

1. Place the rear seatback assembly LH in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Install the rear seatback assembly LH with the 2 bolts.
   

   Torque:

   37 N*m{ 375 kgf*cm , 27 ft.*lbf }

3. Engage the fastener to connect the rear No. 2 floor board sub-assembly.
   

1. Engage the claw to install a new rear seat cushion lock hook.
   

   NOTICE:

   Rear seat cushion lock hooks must not be reused.

   HINT:

   Use the same procedure the LH side and RH side.

1. Place the rear seat cushion assembly in the cabin.
   

   NOTICE:

   Be careful not to damage the vehicle body.

2. Pass the rear center seat outer belt assembly through the rear seat cushion assembly.
   

3. Install the rear center seat outer belt assembly with the bolt.
   

   Torque:

   42 N*m{ 428 kgf*cm , 31 ft.*lbf }

4. Engage the guide as shown in the illustration.
   

5. Pass the rear seat inner with center belt assembly LH and rear seat inner belt assembly through the rear seat cushion assembly as shown in the illustration.
   
   

   
   
   
   
   

   Text in Illustration 

   *1

   Rear Seat Inner Belt Assembly

   *2

   Rear Seat Inner with Center Belt Assembly LH

6. Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.
   

7. Confirm that the seat cushion is firmly installed.
   

   NOTICE:

   When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

1. Align the alignment mark (purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
   

   Text in Illustration 

   *a	Alignment Mark (Purple)

   NOTICE:

   After installation, check that the corners fit correctly.

1. Engage the 4 claws, 2 guides and 2 clips to install the rear door scuff plate LH.
   

1. Engage the 4 clips to install the rear deck trim cover.
   

1. Engage the 2 guides (B).
   

2. Engage the 2 claws and guide (A) to install the deck trim service hole cover.
   

1. Engage the 2 claws and 2 clips.
   

2. Install the rear No. 1 floor board with the bolt.
   

1. Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.
   

1. Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.
   

1. Install the tonneau cover assembly.
   

1. Engage the 6 guides.
   

2. Install the deck floor box LH with the clip.
   

1. Install the rear No. 4 floor board.
   

1. Engage the 2 clips and 3 guides to install the rear No. 4 floor board.
   

1. Engage the 6 guides.
   

2. Install the deck floor box RH with the clip.
   

1. Install the rear No. 3 floor board.
   

1. Install the rear deck floor box.
   

1. Install the rear No. 2 floor board.