LIGHTING SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here

HINT:

The following items can be customized.

NOTICE:

1. When the customer requests a change in a function, first make sure that the function can be customized.
   
2. Be sure to make a note of the current settings before customizing.
   
3. When troubleshooting a function, first make sure that the function is set to the default setting.
   

1. Customizing with the intelligent tester
   
   

   1. Connect the intelligent tester to the DLC3.
      

   2. Turn the power switch to on (IG).
      

   3. Turn the intelligent tester on.
      

   4. Enter the following menus:
      

      1. for Illuminated Entry: Body / Main Body / Utility / Customize / Illuminated Entry.
         
      2. for Light Control: Body / Main Body / Utility / Customize / Light Control.
         

   5. Select the setting by referring to the table below.
      
      

      Illuminated Entry 

      Display	Default	Content	Setting	Relevant ECU
      Mirr-Foot-Lgt Approached	ON	Lights up the door mirror foot lights when a key enters any actuation area around the doors.	ON or OFF	Main Body ECU (Multiplex Network Body ECU)
      Mirr-Foot-Lgt Unlocked	ON	Lights up the door mirror foot lights when doors are unlocked using a mechanical key or door control transmitter.	ON or OFF
      Mirr-Foot-Lgt w/Master SW	ON	Lights up the door mirror foot lights when the driver side door control switch on the multiplex network master switch assembly is pushed to the unlock position. Lights up the door mirror foot lights when the front passenger side door control switch on the power window regulator switch assembly is pushed to the unlock position.	ON or OFF
      Mirror Foot Lighting Time	15 s	Changes the lighting time of the door mirror foot lights.	7.5 s, 15 s, 30 s or 0 s*1
      Exterior Light Control	ON	Changes the door mirror foot light control.	ON or OFF

      1. *1: Even if "0 s" is selected, it can not be set.
         
      
      

      Light Control 

      Display	Default	Content	Setting	Relevant ECU
      Response Time*1	Normal	Changes the delay timing of lighting the taillights when going into a tunnel when the light control switch is in the AUTO position	Normal or Long	Main Body ECU (Multiplex Network Body ECU)
      Sensitivity	Normal	Adjusts the sensitivity of the automatic light control system.	Light2, Light1, Normal, Dark1 or Dark2
      DRL Function*2	ON	ON/OFF of the DRL function	ON or OFF
      Disp Ex ON Sen	Normal	Changes the ambient brightness level required to dim the lights such as the indicator lights of the combination meter, A/C indicator light and clock.	Light2, Light1, Normal, Dark1 or Dark2
      Disp Ex OFF Sen	Normal	Changes the ambient brightness level required to cancel the dimming of the lights such as the indicator lights of the combination meter, A/C indicator light and clock.	Light2, Light1, Normal, Dark1 or Dark2

      1. *1: w/o Light Reminder
         
      2. *2: w/ DRL
         

2. Customizing with the Combination meter assembly
   

   HINT:

   1. Press and hold DISP (steering pad switch) when entering an item.
      
   2. Briefly press DISP (steering pad switch) when selecting an item.
      
   
   

   1. Turn the power switch on (IG).
      

   2. Enter the following menus: SETTINGS / VEHICLE SETTINGS.
      

   3. Select the setting by referring to the table below.
      
      

      Display	Default	Content	Setting	Relevant ECU
      LIGHT SENSOR SENSITIVITY	0 (Standard)	Adjusts the sensitivity of the automatic light control system.*2	-2, -1, 0, 1 or 2	Main Body ECU (Multiplex Network Body ECU)
      DAYTIME RUNNING LIGHTS*1	ON	ON/OFF of the DRL function	ON or OFF
      EXTERIOR LIGHTS OFF TIME ADJUSTMENT	15 s	Changes the lighting time of the door mirror foot lights.	7.5 s, 15 s, 30 s or OFF*3

      1. *1: w/ DRL
         
      2. *2: The higher the setting value is, the more the lights come on easily.
         
      3. *3: Even if "OFF" is selected, it can not be set.