ENGINE UNIT > REASSEMBLY


  1. INSTALL TIGHT PLUG

  2. INSTALL STRAIGHT PIN

  3. INSTALL STUD BOLT

  4. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

  5. INSTALL PISTON SUB-ASSEMBLY WITH PIN

  6. INSTALL PISTON RING SET

  7. INSTALL CRANKSHAFT BEARING

  8. INSTALL CRANKSHAFT

  9. INSTALL CONNECTING ROD BEARING

  10. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

  11. INSTALL RING PIN

  12. INSTALL NO. 1 STRAIGHT SCREW PLUG

  13. INSTALL NO.2 STRAIGHT SCREW PLUG

  14. INSTALL UNION

  15. INSTALL STUD BOLT

  16. INSTALL STRAIGHT PIN

  17. INSTALL VALVE SPRING SEAT

  18. INSTALL VALVE STEM OIL SEAL

  19. INSTALL INTAKE VALVE

  20. INSTALL EXHAUST VALVE

  21. INSTALL VALVE STEM CAP

  22. INSTALL REAR ENGINE OIL SEAL RETAINER

  23. INSTALL WATER OUTLET PIPE SUB-ASSEMBLY

  24. INSTALL CYLINDER BLOCK WATER JACKET SPACER LH

  25. INSTALL CYLINDER BLOCK WATER JACKET SPACER RH

  26. INSTALL CYLINDER HEAD SUB-ASSEMBLY RH

  27. INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

  28. INSTALL VALVE LASH ADJUSTER ASSEMBLY

  29. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

  30. INSTALL CAMSHAFT BEARING CAP RH

  31. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

  32. INSTALL CAMSHAFT BEARING CAP LH

  33. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

  34. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

  35. INSTALL NO. 2 CAMSHAFT TIMING GEARS AND CHAIN (for Bank 1)

  36. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

  37. INSTALL NO. 2 CAMSHAFT TIMING GEARS AND CHAIN (for Bank 2)

  38. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  39. INSTALL NO. 2 CHAIN VIBRATION DAMPER

  40. INSTALL CRANKSHAFT TIMING GEAR OR SPROCKET

  41. INSTALL IDLE SPROCKET ASSEMBLY

  42. INSTALL CHAIN SUB-ASSEMBLY

  43. INSTALL CHAIN TENSIONER SLIPPER

  44. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  45. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY

  46. INSTALL WATER PUMP ASSEMBLY

  47. INSTALL OIL PAN BAFFLE PLATE

  48. INSTALL OIL STRAINER SUB-ASSEMBLY

  49. INSTALL OIL PAN SUB-ASSEMBLY

  50. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  51. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

  52. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

  53. INSTALL WATER BY-PASS JOINT RR

  54. INSTALL WATER INLET WITH THERMOSTAT

  55. INSTALL WATER INLET SUB-ASSEMBLY

  56. INSTALL CRANKSHAFT PULLEY

  57. INSTALL OIL FILTER ELEMENT

  58. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  59. INSTALL NO. 1 OIL PIPE

  60. INSTALL NO. 2 OIL PIPE

  61. INSTALL CRANKSHAFT POSITION SENSOR

  62. INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY LH

  63. INSTALL CAMSHAFT POSITION SENSOR

  64. INSTALL VENTILATION VALVE SUB-ASSEMBLY

  65. INSTALL SPARK PLUG

  66. INSTALL NO. 2 ENGINE HANGER

  67. INSTALL NO. 1 ENGINE HANGER

  68. INSTALL RADIATOR CAP SUB-ASSEMBLY

  69. INSTALL OIL FILLER CAP SUB-ASSEMBLY