SHIFT SOLENOID VALVE > INSPECTION

for Preparation Click here



1. INSPECT SHIFT SOLENOID VALVE SL1


    G020767E19

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    1 - 2
    		5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



2. INSPECT SHIFT SOLENOID VALVE S1


    G023409E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    Solenoid Connector (S1) - Solenoid Body (S1)
    		11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



3. INSPECT SHIFT SOLENOID VALVE S2


    G023407E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    Solenoid Connector (S2) - Solenoid Body (S2)
    		11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



4. INSPECT SHIFT SOLENOID VALVE S3


    G023409E04

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    Solenoid Connector (S3) - Solenoid Body (S3)
    		11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, and check operation of the valve.

    OK:
    The solenoid makes an operating sound.



5. INSPECT SHIFT SOLENOID VALVE S4


    G023408E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    Solenoid Connector (S4) - Solenoid Body (S4)
    		11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



6. INSPECT SHIFT SOLENOID VALVE SL2


    G020767E20

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    1 - 2
    		5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



7. INSPECT SHIFT SOLENOID VALVE SR


    G023410E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    Solenoid Connector (SR) - Solenoid Body (SR)
    		11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



8. INSPECT SHIFT SOLENOID VALVE SLT


    G020767E21

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    1 - 2
    		5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, and check operation movement of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.



9. INSPECT SHIFT SOLENOID VALVE SLU


    G020767E22

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    		Specified Condition
    20°C (68°F)
    1 - 2
    		5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, and check operation of the valve.

    NOTICE:
    While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    OK:
    The solenoid makes an operating sound.