CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit

for Preparation Click here


DESCRIPTION

The cruise control main switch operates 7 functions: SET, COAST, TAP-DOWN, RESUME, ACCEL, TAP-UP, and CANCEL. The SET, TAP-DOWN and COAST functions, and the RESUME, TAP-UP and ACCEL functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control SET, COAST, RESUME, ACCEL and CANCEL.

WIRING DIAGRAM


E109062E01


INSPECTION PROCEDURE

1.READ VALUE OF INTELLIGENT TESTER
E107091E01

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the intelligent tester main switch ON.

  1. Check the Data List for proper functioning of the cruise control main switch.

    ECM (Cruise control): 
    Item
    		Measurement Item / Display (Range)
    		Normal Condition
    		Diagnostic Note
    Main SW (Main)
    		Main switch signal (Main CPU) / ON or OFF
    		ON: Main switch ON (Pushed on)
    OFF: Main switch OFF (Pushed off)
    		-
    Cancel SW
    		Cancel switch signal / ON or OFF
    		ON: Cancel switch ON
    OFF: Cancel switch OFF
    		-
    SET/COAST SW
    		SET / COAST switch signal / ON or OFF
    		ON: SET / COAST switch ON
    OFF: SET / COAST switch OFF
    		-
    RES/ACC SW
    		RES / ACC switch signal / ON or OFF
    		ON: RES / ACC switch ON
    OFF: RES / ACC switch OFF
    		-

    OK:
    When cruise control main switch operation is performed, the results will be same as above.

    Result: 
    Result
    		Proceed to
    OK
    		A
    NG (All items are defective)
    		B
    NG (1 to 3 items are defective)
    		C



A
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE CRUISE CONTROL MAIN SWITCH
B


2.INSPECT CRUISE CONTROL MAIN SWITCH

  1. Disconnect the cruise control main switch connector.



  1. Measure the resistance according to the value(s) in the table below.


    E106137E01


Standard resistance:

Tester Connection
Switch Condition
Specified Condition
1 - 3
Neutral
10 kΩ or higher
1 - 3
RES / ACC
235 to 245 Ω
1 - 3
SET / COAST
620 to 640 Ω
1 - 3
CANCEL
1,510 to 1,570 Ω
1 - 3
Main Switch OFF
10 kΩ or higher
1 - 3
Main Switch ON
Below 1 Ω



NG
REPLACE CRUISE CONTROL MAIN SWITCH
OK


3.INSPECT SPIRAL CABLE
E106780E03

  1. Disconnect the spiral cable connectors.

  1. Measure the resistance of the connectors.

    Standard resistance:
    Tester Connection
    		Specified Condition
    A-3 - L20-1
    		Below 1 Ω
    A-4 - L20-2
    		Below 1 Ω



NG
REPLACE SPIRAL CABLE
OK


4.CHECK WIRE HARNESS (SPIRAL CABLE - ECM AND BODY GROUND)


    E108174E03

  1. Disconnect the A7 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    		Condition
    		Specified Condition
    L20-1 - A7-31 (CCS)
    		Always
    		Below 1 Ω
    A7-31 (CCS) - Body ground
    		Always
    		10 kΩ or higher
    L20-2 - Body ground
    		Always
    		Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE