DTC B2417 Headlight Beam Level Control Motor LH Malfunction |
DTC B2418 Headlight Beam Level Control Motor RH Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2417 |
|
|
| B2418 |
|
|

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the Active Test and then check the motor operation.
| Item | Test Details | Diagnostic Note |
| Drive The Leveling Motor | Drive the leveling motor UP / OFF (OFF) | - |
| Drive The Leveling Motor | Drive the leveling motor DOWN / OFF (OFF) | - |
| OK (When checking from PROBLEM SYMPTOMS TABLE) | A |
| OK (When checking from DIAGNOSTIC TROUBLE CODE CHART) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 2.CHECK WIRE HARNESS (HEADLIGHT BEAM LEVEL CONTROL MOTOR - AFS ECU) |

Disconnect the B11 and B2 headlight assembly connectors.
Disconnect the A30 AFS ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Condition | Specified Condition |
| A30-29(LL1+) - B11-15(LL1+) | Always | Below 1 Ω |
| A30-30(LL1-) - B11-14(LL1-) | Always | Below 1 Ω |
| A30-31(LL2+) - B11-13(LL2+) | Always | Below 1 Ω |
| A30-32(LL2-) - B11-12(LL2-) | Always | Below 1 Ω |
| A30-29(LL1+) - Body ground | Always | 10 kΩ or higher |
| A30-30(LL1-) - Body ground | Always | 10 kΩ or higher |
| A30-31(LL2+) - Body ground | Always | 10 kΩ or higher |
| A30-32(LL2-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A30-13(LR1+) - B2-15(LR1+) | Always | Below 1 Ω |
| A30-14(LR1-) - B2-14(LR1-) | Always | Below 1 Ω |
| A30-15(LR2+) - B2-13(LR2+) | Always | Below 1 Ω |
| A30-16(LR2-) - B2-12(LR2-) | Always | Below 1 Ω |
| A30-13(LR1+) - Body ground | Always | 10 kΩ or higher |
| A30-14(LR1-) - Body ground | Always | 10 kΩ or higher |
| A30-15(LR2+) - Body ground | Always | 10 kΩ or higher |
| A30-16(LR2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT HEADLIGHT LEVELING MOTOR RH |
![]() |
Measure the resistance of the connector.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 5.8 to 12.5 Ω |
| 3 - 4 | Always | 5.8 to 12.5 Ω |
| OK (When checking from DIAGNOSTIC TROUBLE CODE CHART) | A |
| OK (When checking from PROBLEM SYMPTOMS TABLE) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT HEADLIGHT LEVELING MOTOR LH |
![]() |
Measure the resistance of the connector.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 5.8 to 12.5 Ω |
| 3 - 4 | Always | 5.8 to 12.5 Ω |
| OK (When checking from DIAGNOSTIC TROUBLE CODE CHART) | A |
| OK (When checking from PROBLEM SYMPTOMS TABLE) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||