REAR SEAT INNER BELT ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE REAR SEAT CUSHION ASSEMBLY


B105946E01

  1. Detach the seat cushion's 2 front hooks from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat for the other hook.

  1. Detach the seat cushion's 2 rear hooks from the seatback.

  1. Remove the seat cushion.



3. REMOVE REAR SEAT BELT OUTER ANCHOR


B107409E01

  1. Remove the bolt and anchor.



4. REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH


B107410E02

  1. Disconnect the connector labeled A.

  1. Remove the bolt and the anchor part of the rear seat inner with center belt assembly RH labeled B.



5. REMOVE REAR SEAT WITH CENTER BELT ASSEMBLY LH


B107411E01

  1. Disconnect the connector labeled A.

  1. Remove the bolt and the anchor part of the rear seat inner with center belt assembly LH labeled B.



6. REMOVE REAR SEAT HEADREST ASSEMBLY RH AND LH


7. REMOVE REAR SEATBACK ASSEMBLY



B105947

  1. Using a screwdriver, detach the claws and remove the 2 rear seat covers.

    HINT:
    Tape the screwdriver tip before use.



    B105996E01

  1. Using a screwdriver, detach the claw to open the cap of the 3 rear seat shoulder belt guides.

  1. Remove the bolt and floor anchor part.



    B105948

  1. Remove the 4 bolts and 2 nuts.

  1. Remove the seatback.



8. REMOVE REAR DOOR SCUFF PLATE


B111627E01

  1. Using a moulding remover, detach the 5 claws and remove the scuff plate.



9. REMOVE REAR SEAT SIDE GARNISH


B111632

  1. Using a moulding remover, pull the garnish in the direction indicated by the arrow in the illustration to detach the 5 claws. Then remove the garnish.



10. REMOVE ROOF SIDE GARNISH INNER


B111633

  1. Detach the 4 clips.

  1. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



11. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Sunshade)


    B111292E01

  1. Using a moulding remover, detach the 4 claws and remove the belt guide LH.

    HINT:
    Use the same procedures described for the RH side.



    B111293E03

  1. Using a moulding remover, detach the 4 claws and remove the belt guide center.



    B110339E01

  1. Detach the clip and remove the panel.



12. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


B111292E01

  1. Using a moulding remover, detach the 4 claws and remove the guide part of the rear seat outer belt assembly.



    B111293E03

  1. Using a moulding remover, detach the 4 claws and remove the guide part of the rear seat inner with center belt assembly RH.



    B109353E02

  1. Detach the clip and 5 claws.

  1. Disconnect the connector and remove the package tray trim panel.



13. REMOVE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH


    B107413

  1. Remove the bolt and rear seat inner with center belt assembly RH.