REAR SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR SEAT OUTER BELT ASSEMBLY


B110332E01

  1. Align the seat belt positioning hole with the claw and install the retractor of the seat belt with the 2 bolts. First install the rear bolt, and then install the front bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf } for bolt B



    B109360

  1. Connect the pretensioner connector, as shown in the illustration.

  1. Connect the tension reducer connector.



2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Sunshade)


    B110339E01

  1. Attach the clip to install the package tray trim panel.

  1. Attach the 4 claws to install the belt guide center.



    B111292E01

  1. Attach the 4 claws to install the belt guide.



    B111293E03

  1. Attach the 4 claws to install the belt guide.



3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY


    B109353E02

  1. Install the package tray trim panel.

    1. Connect the connector.

    2. Attach the 5 claws and clip to install the panel.



4. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH


B100959E04

  1. Install the anchor part of the rear seat inner with center belt assembly RH seat belt with the bolt as shown in the illustration.

  1. Connect the connector labeled A.

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



5. INSTALL REAR SEAT OUTER BELT ANCHOR


B100960E02

  1. Install the anchor part of the rear seat outer belt assembly with the bolt.

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



6. INSTALL ROOF SIDE GARNISH

  1. Attach the 2 claws and 4 clips, and install the garnish.



7. INSTALL REAR SEAT SIDE GARNISH


B111645E01

  1. Attach the 5 claws and install the garnish.

  1. Pull out the folded lip of the weatherstrip.



8. INSTALL REAR DOOR SCUFF PLATE


B111646E01

  1. Attach the 5 claws to install the scuff plate.

  1. Pull out the folded lip of the weatherstrip.



9. INSTALL REAR SEATBACK ASSEMBLY


B105948

  1. Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the seatback with the 4 bolts and 2 nuts.

    Torque:
    18.1 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Install the 2 rear seat covers.

  1. Pass the 3 seat belts through and close the cap of the 3 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.



10. INSTALL REAR SEAT HEADREST ASSEMBLY RH AND LH


11. INSTALL REAR SEAT CUSHION ASSEMBLY


B105974E01

  1. Attach the seat cushion's 2 rear hooks to the seatback.

  1. Attach the seat cushion's 2 front hooks to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.



12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


13. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.