REAR SEAT OUTER BELT ASSEMBLY > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the RH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative battery terminal to prevent airbag and seat belt pretensioner activation.



2. REMOVE REAR SEAT CUSHION ASSEMBLY


B105946E01

  1. Detach the seat cushion's 2 front hooks from the vehicle body.

    NOTICE:
    Follow the instructions below carefully as the cushion frame deforms easily.


    1. Choose a hook to detach first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to detach the hook.

    2. Repeat for the other hook.

  1. Detach the seat cushion's 2 rear hooks from the seatback.

  1. Remove the seat cushion.



3. REMOVE REAR SEAT HEADREST ASSEMBLY RH AND LH


4. REMOVE REAR SEATBACK ASSEMBLY



B105947

  1. Using a screwdriver, detach the claws and remove the 2 rear seat covers.

    HINT:
    Tape the screwdriver tip before use.



    B105996E01

  1. Using a screwdriver, detach the claw to open the cap of the 3 rear seat shoulder belt guides.

  1. Remove the bolt and floor anchor part.



    B105948

  1. Remove the 4 bolts and 2 nuts.

  1. Remove the seatback.



5. REMOVE REAR DOOR SCUFF PLATE


B111629

  1. Detach the 5 claws and remove the scuff plate.



6. REMOVE REAR SEAT SIDE GARNISH


B111632

  1. Using a moulding remover, pull the garnish in the direction indicated by the arrow in the illustration to detach the 5 claws. Then remove the garnish.



7. REMOVE ROOF SIDE GARNISH


B111633

  1. Detach the 4 clips.

  1. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.



8. REMOVE REAR SEAT OUTER BELT ANCHOR


    B107409

  1. Remove the bolt and anchor part of the rear seat outer belt assembly.



9. REMOVE REAR SEAT INNER WITH CENTER BELT ANCHOR RH


B107410E01

  1. Disconnect the connector labeled A.

  1. Remove the bolt and seat belt labeled B.



10. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Sunshade)


    B111292E01

  1. Using a moulding remover, detach the 4 claws and remove the belt guide LH.

    HINT:
    Use the same procedures described for the RH side.



    B111293E03

  1. Using a moulding remover, detach the 4 claws and remove the belt guide center.



    B110339E01

  1. Detach the clip and remove the panel.



11. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


B111292E01

  1. Using a moulding remover, detach the 4 claws and remove the guide part of the rear seat outer belt assembly.



    B111293E03

  1. Using a moulding remover, detach the 4 claws and remove the guide part of the rear seat inner with center belt assembly RH.



    B109353E02

  1. Detach the clip and 5 claws.

  1. Disconnect the connector and remove the package tray trim panel.



12. REMOVE REAR SEAT OUTER BELT ASSEMBLY


    B106128E03

  1. Disconnect the pretensioner connector, as shown in the illustration.

  1. Disconnect the tension reducer connector.



    B109340E01

  1. Remove the 2 bolts and seat belt.