PARKING BRAKE CABLE > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY


B105917E01

  1. Using a screwdriver, detach the 2 claws and remove the front seat belt hole cover.

    HINT:
    Tape the screwdriver tip before use.



    B105918E01

  1. Apply protective tape around the seat belt anchor cover cap to the cushion shield.

  1. Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.

    HINT:
    Tape the screwdriver tip before use.

  1. Move the seat using the power seat switch knob so that the seat belt anchor bolt is revealed.



    B105919

  1. Remove the bolt and front seat outer belt anchor.



3. REMOVE FRONT SEAT ASSEMBLY


B105920E01

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover front inner and outer.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 2 bolts on the front side of the seat.

  1. Operate the power seat switch knob and move the seat to the foremost position.



    B105921E01

  1. Using a screwdriver, detach the 4 claws and remove the seat track bracket cover rear inner and outer.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Disconnect the connectors under the seat. Then remove the seat.



4. REMOVE CONSOLE UPPER PANEL GARNISH FRONT


B111912

  1. Using a clip remover, detach the claws and remove the garnish.

    HINT:
    Tape the clip remover tip before use.



5. REMOVE FRONT ASH RECEPTACLE ASSEMBLY


B110191

  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.



    B111908E01

  1. Using a screwdriver, detach the 9 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the ash receptacle and then disconnect the connector.



6. REMOVE INSTRUMENT PANEL FINISH LH PANEL END


B105636E09

  1. Remove the screw.

  1. Using a screwdriver, detach the 4 clips and 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the finish panel end.



7. REMOVE INSTRUMENT PANEL FINISH RH PANEL END


B105637E06

  1. Remove the screw.

  1. Using a screwdriver, detach the 3 clips and 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the finish panel end.



8. REMOVE CONSOLE BOX PLATE


B105638E06

  1. Using a screwdriver, detach the 4 clips.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the console box plate and then disconnect the connector.



9. REMOVE CONSOLE BOX REGISTER ASSEMBLY


B105635E01

  1. Using a screwdriver, detach the 4 clips and remove the register.

    HINT:
    Tape the screwdriver tip before use.



10. REMOVE CONSOLE BOX


B106268

  1. Remove the 4 bolts and 2 screws.

  1. Remove the console box and then disconnect the connector.



11. REMOVE FRONT FLOOR BRACE CENTER (for 3GR-FSE)


A109952

  1. Remove the 4 bolts and floor brace.



12. DISCONNECT HEATED OXYGEN SENSOR (for 3GR-FSE)

  1. Remove the 2 sensors from the front exhaust pipe (Click here).



13. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 3GR-FSE)


A106753

  1. Remove the 4 bolts and 4 nuts.

  1. Disconnect the exhaust pipe front ends from the exhaust manifold and remove the 2 gaskets.

  1. Remove the 2 bolts, 2 compression springs, exhaust pipe and gasket.



14. REMOVE FRONT FLOOR HEAT NO.1 INSULATOR (for 3GR-FSE)

  1. Remove the 4 nuts, grommet and front floor heat insulator No.1.



15. REMOVE REAR PROPELLER SHAFT ASSEMBLY (for 3GR-FSE)


    C104521E01

  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.



    F048233

  1. Remove the 2 bolts, 2 center support bearing washers and center support bearing.



    C109590E01

  1. Insert SST in the transmission to prevent oil leakage.

    SST
    09325-40010  

    NOTICE:
    Be careful not to damage the oil seal.



16. REMOVE FRONT FLOOR BRACE CENTER (for 3GR-FE)


A109952

  1. Remove the 4 bolts and floor brace.



17. DISCONNECT HEATED OXYGEN SENSOR (for 3GR-FE)

  1. Remove the 2 sensors from the front exhaust pipe (Click here).



18. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 3GR-FE)
(Click here)


19. REMOVE FRONT FLOOR HEAT NO.1 INSULATOR (for 3GR-FE)

  1. Remove the 4 nuts, grommet and front floor heat insulator No.1.



20. REMOVE REAR PROPELLER SHAFT ASSEMBLY (for 3GR-FE)


    C104521E01

  1. Put matchmarks on both flanges.

  1. Remove the 4 nuts, bolts and washers.

    HINT:
    If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.



    F048233

  1. Remove the 2 bolts, 2 center support bearing washers and center support bearing.



    C109590E01

  1. Insert SST in the transmission to prevent oil leakage.

    SST
    09325-40010  

    NOTICE:
    Be careful not to damage the oil seal.



21. REMOVE FRONT FLOOR BRACE CENTER (for 3UZ-FE)


A109580

  1. Remove the 4 bolts and floor brace.



22. REMOVE REAR NO.1 FLOOR PANEL BRACE (for 3UZ-FE)


A104870

  1. Remove the 4 bolts and panel brace.



23. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 3UZ-FE)


A101964E02

  1. Remove the 4 bolts and 4 nuts.

  1. Disconnect the exhaust pipe front ends from the 2 TWCs and remove the 2 gaskets.

  1. Remove the 2 bolts, 2 compression springs, exhaust pipe and gasket.



24. REMOVE FRONT FLOOR HEAT NO.1 INSULATOR (for 3UZ-FE)

  1. Remove the 4 nuts and front floor heat insulator No.1.



25. REMOVE REAR PROPELLER SHAFT ASSEMBLY (for 3UZ-FE)


    C109597E01

  1. Using SST, loosen the adjusting nut until it can be turned by hand.

    SST
    09922-10010  

    HINT:
    Use 2 same type of SST.



    C101199E01

  1. Put matchmarks on the transmission companion flange, flexible coupling and intermediate shaft.

  1. Remove the 3 bolts, 3 washers and 3 nuts.

    NOTICE:
    The propeller shaft and flexible coupling should not be separated.



    C109598E01

  1. Put matchmarks on the differential companion flange, flexible coupling and propeller shaft.

  1. Remove the 3 bolts, 3 washers and 3 nuts.

    NOTICE:
    The propeller shaft and flexible coupling should not be separated.



    C101198E01

  1. Remove the 2 bolts and 2 center support bearing washers.

    HINT:
    Some vehicles are not equipped with the center support bearing washers.



    C101200

  1. Push the rear propeller shaft straight forward to compress the propeller shaft and pull out the propeller shaft from the centering pin of the differential.

    NOTICE:
    Press the propeller shaft straight ahead to keep the transmission and intermediate shaft aligned straight.

    HINT:
    If it is difficult to separate the flange from the flexible coupling, pry it using a screwdriver.

  1. Pull the propeller shaft outward from the vehicle's rear.

    NOTICE:
    The intermediate shaft and propeller shaft should not be separated.



26. REMOVE DIFFERENTIAL SUPPORT NO.2 PROTECTOR


    G033363

  1. Remove the 2 nuts and differential support protector No.2 from the suspension member brace.



27. REMOVE REAR WHEEL


28. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    G032829

  1. Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Hang the caliper with wire or equivalent.

  1. Remove the caliper No.1 plate (2 pieces).



29. REMOVE REAR DISC

  1. Release the parking brake.



    C107205E01

  1. Put matchmarks on the rear disc and rear axle hub.

  1. Remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns smoothly.



30. REMOVE PARKING BRAKE SHOE RETURN NO.2 SPRING


    C104639E01

  1. Using SST, remove the parking brake shoe return No.2 spring.

    SST
    09703-30011  



31. REMOVE PARKING BRAKE SHOE RETURN NO.1 SPRING


    C104640E01

  1. Using SST, remove the parking brake shoe return No.1 spring.

    SST
    09703-30011  



32. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    G033601

  1. Slide the parking brake shoe, and remove the parking brake shoe adjusting screw set.



33. REMOVE PARKING BRAKE NO.1 SHOE ASSEMBLY


    G032834E01

  1. Using SST, remove the shoe hold down spring No.1 cup, compression No.1 spring and shoe hold down spring No.1 pin.

    SST
    09718-00010  

  1. Remove the parking brake No.1 shoe assembly.



34. REMOVE PARKING BRAKE NO.2 SHOE ASSEMBLY


    C107309E01

  1. Using SST, remove the shoe hold down spring No.1 cup, compression No.1 spring and shoe hold down spring No.1 pin.

    SST
    09718-00010  

  1. Remove the parking brake No.2 shoe assembly.

    HINT:
    Use the service hole to retain the hold down spring No.1 pin with your finger.



35. REMOVE PARKING BRAKE SHOE LEVER


36. REMOVE PARKING BRAKE NO.3 CABLE ASSEMBLY

  1. Remove the 3 bolts and disengage the 2 clamps and parking brake No.3 cable assembly.



  1. Separate the parking brake No.3 cable assembly from the parking brake equalizer.


    C106342



    G032828

  1. Remove the 2 nuts and parking brake No.3 cable assembly.



    C107206E01

  1. Remove the 2 cable support brackets from the parking brake No.3 cable assembly.