RADIATOR > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent aribag activation.



2. REMOVE ENGINE UNDER COVER


B107493

  1. Using a clip remover, remove the 3 clips.

  1. Remove the 10 screws and under cover.



3. REMOVE COOL AIR INTAKE DUCT SEAL


B106147

  1. Using a clip remover, remove the 7 clips and duct seal.



4. REMOVE ENGINE ROOM SIDE COVER RH


    A110866E01

  1. Remove the nut, 2 clips and side cover.



5. REMOVE ENGINE ROOM SIDE COVER LH


    A110867E01

  1. Remove the 3 clips and side cover.



6. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. Remove the 2 nuts and cover.



7. REMOVE NO. 1 AIR CLEANER INLET

  1. Remove the bolt and inlet.



8. REMOVE INTAKE AIR CONNECTOR PIPE


    A105826

  1. Disconnect the air hose and No. 1 ventilation hose.

  1. Loosen the 2 hose clamps and remove the intake air connector.



9. REMOVE AIR CLEANER ASSEMBLY

  1. Disconnect the MAF meter connector and clamp.

  1. Remove the 3 bolts and air cleaner assembly.



10. DISCONNECT RADIATOR HOSE INLET


A110188

  1. Disconnect the hose inlet.



11. DISCONNECT RADIATOR HOSE OUTLET


A100509

  1. Disconnect the hose outlet.



12. DISCONNECT NO. 1 OIL COOLER INLET TUBE


A100510

  1. Disconnect the tube from the radiator.



13. DISCONNECT NO. 1 OIL COOLER OUTLET TUBE


A100511

  1. Disconnect the tube from the radiator.

  1. Detach the tube from the radiator's clamp.



14. REMOVE FRONT BUMPER COVER

  1. Using a clip remover, remove the 2 clips.

    HINT:
    Put protective tape under the front fender.



    B109982

  1. Remove the 6 screws and 5 bolts.



    B106150E01

  1. Pull the bumper cover to detach the 3 claws on the LH side.

  1. Pull the bumper cover to detach the 3 claws on the RH side and remove the bumper cover.

  1. w/ Clearance sonar system:
    Disconnect the ultrasonic sensor connector.



15. REMOVE RADIATOR SUPPORT OPENING COVER


B107497E01

  1. Remove the 4 clips and cover.



16. REMOVE HOOD LOCK CONTROL CABLE COVER


B109041E01

  1. Remove the 3 screws.

  1. Detach the claw and remove the cable cover.



17. REMOVE HOOD LOCK ASSEMBLY


B109039E01

  1. Disconnect the hood lock control cable.

  1. Remove the cap.

  1. Remove the 2 bolts and nut.

  1. Remove the hood lock.



18. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


  1. Using a clip remover, detach the 6 clamps and remove the wire harness.


    E109816E01



    E107645

  1. Disconnect the connectors.

  1. Remove the 5 bolts and radiator support.



19. REMOVE RADIATOR ASSEMBLY

  1. Disconnect the wire harness from the cooling fan ECU.



    A110189

  1. Remove the 4 bolts.



    A110190E01

  1. Detach the ECM outlet duct.

  1. Remove the radiator from the engine room.



    A110191

  1. Disconnect the reservoir hose.



    A110192

  1. Detach the 3 claws and remove the fan.



    A110193

  1. Remove the 2 radiator support cushions and 2 radiator lower supports from the radiator.