STARTER > INSTALLATION

for Preparation Click here



1. INSTALL STARTER ASSEMBLY


A094953E08

  1. Install the starter with the 2 bolts.

    Torque:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }

  1. Install the starter cable with the nut, and then attach the terminal cap.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the starter connector.



2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A096590E02

  1. Install a new gasket and the manifold with 6 new nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A105951

  1. Connect the A/F sensor connector (bank 1 sensor 1).



    A106410

  1. Install the engine wire bracket.

  1. Install the ground cable with the 2 bolts.



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  1. Install the front exhaust pipe (Click here).

  1. Connect the heated oxygen sensor (Click here).

  1. Install the front floor brace center (Click here).



4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


5. CHECK FOR EXHAUST LEAKS
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


6. INSTALL ENGINE UNDER COVER


B107493

  1. Install the under cover with the 3 clips and 10 screws.



7. INSTALL ENGINE ROOM SIDE COVER LH


A105934E01

  1. Install the side cover with the 3 clips.



8. INSTALL COOL AIR INTAKE DUCT SEAL


B106147

  1. Install the duct seal with the 7 clips.



9. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. Install the cover with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



10. INSTALL FRONT SEAT ASSEMBLY LH


B105963E02

  1. Place the seat in the cabin.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    36.8 N*m{ 375 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the 2 bolts in the order indicated in the illustration.

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. Tighten the 2 bolts on the rear side of the seat.

    Torque:
    36.8 N*m{ 375 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the 2 bolts in the order indicated in the illustration.



11. INSTALL CONSOLE BOX


B106268

  1. Connect the connector.

  1. Install the console box with the 4 bolts and 2 screws.



12. INSTALL CONSOLE BOX REGISTER ASSEMBLY


B105635E04

  1. Attach the 4 clips to install the register.



13. INSTALL CONSOLE BOX PLATE


B105638E10

  1. Connect the connector.

  1. Attach the 4 clips to install the console box.



14. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


B105636E10

  1. Attach the 4 clips and 3 claws to install the finish panel end.

  1. Install the screw.



15. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


B105637E08

  1. Attach the 3 clips and 3 claws to install the finish panel end.

  1. Install the screw.



16. INSTALL CONSOLE UPPER PANEL ASSEMBLY


B111908E02

  1. Connect the connector.

  1. Attach the 9 clips to install the ash receptacle.



    B110192

  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



17. INSTALL FRONT CONSOLE UPPER PANEL GARNISH

  1. Attach the claws to install the garnish.



18. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.