RADIO ANTENNA CORD > INSTALLATION

for Preparation Click here


HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).



1. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY



E108007E04



E109865E02

  1. Attach the 6 clips labeled A.

  1. Attach the antenna cord protector's 3 clips labeled B to the floor stud bolts.

  1. Install the 3 bolts labeled C.

  1. Connect the connectors labeled D.



2. INSTALL REAR SEAT SIDE GARNISH RH

HINT:
Use the same procedures described for the LH side.



3. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



4. INSTALL REAR SEATBACK ASSEMBLY


B105948

  1. Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the seatback with the 4 bolts and 2 nuts.

    Torque:
    18.1 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Install the 2 rear seat covers.

  1. Pass the 3 seat belts through and close the cap of the 3 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.



5. INSTALL REAR SEAT HEADREST ASSEMBLY LH AND RH


6. INSTALL REAR SEAT HEADREST ASSEMBLY CENTER


7. INSTALL REAR SEAT CUSHION ASSEMBLY


B105974E01

  1. Attach the seat cushion's 2 rear hooks to the seatback.

  1. Attach the seat cushion's 2 front hooks to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.



8. INSTALL ANTENNA CORD SUB-ASSEMBLY



E108006E02

  1. Attach the clip labeled A.

  1. Connect the connector labeled B.



9. INSTALL MULTI-DISPLAY WITH RADIO RECEIVER ASSEMBLY

  1. Connect the connectors.



    E107980

  1. Insert the multi-display with radio receiver and attach the 2 clips on its backside.



    E107370

  1. Install the multi-display with radio receiver with the 4 bolts.



10. INSTALL CONSOLE BOX


B106268

  1. Connect the connector.

  1. Install the console box with the 4 bolts and 2 screws.



11. INSTALL CONSOLE BOX REGISTER ASSEMBLY


B105635E04

  1. Attach the 4 clips to install the register.



12. INSTALL CONSOLE BOX PLATE


B105638E10

  1. Connect the connector.

  1. Attach the 4 clips to install the console box.



13. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


B105636E10

  1. Attach the 4 clips and 3 claws to install the finish panel end.

  1. Install the screw.



14. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


B105637E08

  1. Attach the 3 clips and 3 claws to install the finish panel end.

  1. Install the screw.



15. INSTALL CONSOLE UPPER PANEL ASSEMBLY


B111908E02

  1. Connect the connector.

  1. Attach the 9 clips to install the ash receptacle.



    B110192

  1. Install the shift lever knob and twist it in the direction indicated by the arrow.



16. INSTALL FRONT CONSOLE UPPER PANEL GARNISH

  1. Attach the claws to install the garnish.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


18. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.