CAMSHAFT POSITION SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL CAMSHAFT POSITION SENSOR


    B002632

  1. Install the sensor with the bolt and stud bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



2. INSTALL NO. 3 TIMING BELT COVER SUB-ASSEMBLY LH


    A014424E01

  1. Install the gasket to the cover.

  1. Pass the camshaft position sensor wire through the cover hole.

  1. Install the cover with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the wire grommet to the cover.

  1. Install the sensor connector to the sensor holder.

  1. Connect the sensor connector.

  1. Install the sensor wire to the wire clamp on the cover.

  1. Install the engine wire to the 2 wire clamps on the cover.



3. INSTALL OIL COOLER PIPE


    A108784E02

  1. Connect the 3 water by-pass hoses as shown in the illustration.

  1. Install the oil cooler pipe to the cover with the cap nut and the bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. INSTALL RADIATOR HOSE INLET


5. INSTALL V-BANK COVER

  1. Install the V-bank cover with the 2 nuts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



6. INSTALL ENGINE ROOM SIDE COVER LH


    A110867E01

  1. Install the side cover with the 3 clips.



7. INSTALL COOL AIR INTAKE DUCT SEAL


    A110865E01

  1. Install the intake duct seal with the 7 clips.



8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


9. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



10. ADD ENGINE COOLANT

  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    12.7 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Add engine coolant.

    HINT:
    Add engine coolant until coolant overflows from the vent plug.

    Specified capacity:
    11.0 liters (11.7 US qts, 9.7 lmp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Please contact your TOYOTA dealer for further details.

  1. Install the vent plug.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      Adjust the air conditioner set temperature to MAX (HOT).

    2. Maintain the engine speed at 2,000 to 2,500 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      NOTICE:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      1. Be careful as the radiator hoses are hot.
      1. Keep your hands away from the radiator fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A110178E01

  1. Check the coolant level in the radiator reservoir.
    If the coolant level is low, add SLLC to the radiator reservoir FULL line.



11. CHECK FOR ENGINE COOLANT LEAKS

  1. Check for engine coolant leaks (Click here).