POWER SEAT SWITCH > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER SEAT SWITCH RH


B105969E01

  1. Measure the resistance between the terminals when each switch is operated.

    Standard resistance (Slide switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 9 (SLDF)
    		FRONT
    		Below 1 Ω
    4 (E) - 6 (SLDR)
    		FRONT
    		Below 1 Ω
    4 (E) - 6 (SLDR)
    		OFF
    		Below 1 Ω
    4 (E) - 9 (SLDF)
    		OFF
    		Below 1 Ω
    1 (B) - 6 (SLDR)
    		REAR
    		Below 1 Ω
    4 (E) - 9 (SLDF)
    		REAR
    		Below 1 Ω

    Standard resistance (Front vertical switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 5 (FUP)
    		UP
    		Below 1 Ω
    4 (E) - 10 (FDWN)
    		UP
    		Below 1 Ω
    4 (E) - 5 (FUP)
    		OFF
    		Below 1 Ω
    4 (E) - 10 (FDWN)
    		OFF
    		Below 1 Ω
    1 (B) - 5 (FUP)
    		DOWN
    		Below 1 Ω
    1 (B) - 10 (FDWN)
    		DOWN
    		Below 1 Ω

    Standard resistance (Lifter switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 8 (LUP)
    		UP
    		Below 1 Ω
    4 (E) - 7 (LDWN)
    		UP
    		Below 1 Ω
    4 (E) - 7 (LDWN)
    		OFF
    		Below 1 Ω
    4 (E) - 8 (LUP)
    		OFF
    		Below 1 Ω
    1 (B) - 7 (LDWN)
    		DOWN
    		Below 1 Ω
    4 (E) - 8 (LUP)
    		DOWN
    		Below 1 Ω

    Standard resistance (Reclining switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 3 (RCLF)
    		FRONT
    		Below 1 Ω
    2 (RCLR) - 4 (E)
    		FRONT
    		Below 1 Ω
    2 (RCLR) - 4 (E)
    		OFF
    		Below 1 Ω
    3 (RCLF) - 4 (E)
    		OFF
    		Below 1 Ω
    1 (B) - 2 (RCLR)
    		REAR
    		Below 1 Ω
    3 (RCLF) - 4 (E)
    		REAR
    		Below 1 Ω

    If the result is not as specified, replace the switch.



2. INSPECT FRONT POWER SEAT SWITCH LH


B105970E01

  1. Measure the resistance between the terminals when each switch is operated.

    Standard resistance (Slide switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 9 (SLDF)
    		FRONT
    		Below 1 Ω
    4 (E) - 6 (SLDR)
    		FRONT
    		Below 1 Ω
    4 (E) - 6 (SLDR)
    		OFF
    		Below 1 Ω
    4 (E) - 9 (SLDF)
    		OFF
    		Below 1 Ω
    1 (B) - 6 (SLDR)
    		REAR
    		Below 1 Ω
    4 (E) - 9 (SLDF)
    		REAR
    		Below 1 Ω

    Standard resistance (Front vertical switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 10 (FUP)
    		UP
    		Below 1 Ω
    4 (E) - 5 (FDWN)
    		UP
    		Below 1 Ω
    4 (E) - 10 (FUP)
    		OFF
    		Below 1 Ω
    4 (E) - 5 (FDWN)
    		OFF
    		Below 1 Ω
    1 (B) - 10 (FUP)
    		DOWN
    		Below 1 Ω
    1 (B) - 5 (FDWN)
    		DOWN
    		Below 1 Ω

    Standard resistance (Lifter switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 7 (LUP)
    		UP
    		Below 1 Ω
    4 (E) - 8 (LDWN)
    		UP
    		Below 1 Ω
    4 (E) - 7 (LDWN)
    		OFF
    		Below 1 Ω
    4 (E) - 7 (LUP)
    		OFF
    		Below 1 Ω
    1 (B) - 8 (LDWN)
    		DOWN
    		Below 1 Ω
    4 (E) - 7 (LUP)
    		DOWN
    		Below 1 Ω

    Standard resistance (Reclining switch):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (B) - 3 (RCLF)
    		FRONT
    		Below 1 Ω
    2 (RCLR) - 4 (E)
    		FRONT
    		Below 1 Ω
    2 (RCLR) - 4 (E)
    		OFF
    		Below 1 Ω
    3 (RCLF) - 4 (E)
    		OFF
    		Below 1 Ω
    1 (B) - 2 (RCLR)
    		REAR
    		Below 1 Ω
    3 (RCLF) - 4 (E)
    		REAR
    		Below 1 Ω

    If the result is not as specified, replace the switch.